background image

12

TROUBLESHOOTING CONT’D

9.2 TESTS

NOTICE:

Service on this, or any other, LANG appliance must be
performed by qualified personnel only.  Consult your
authorized service station directory or call the factory
at 1-800-224-LANG (5264), or WWW.LANGWORLD.COM
for the service station nearest you.

WARNING:

BOTH HIGH AND LOW VOLTAGES ARE PRESENT
INSIDE THIS APPLIANCE WHEN THE UNIT IS
PLUGGED/WIRED INTO A LIVE RECEPTACLE.
BEFORE REPLACING ANY PARTS, DISCONNECT THE
UNIT FROM THE ELECTRIC POWER SUPPLY.

If an item on the list is followed by an asterisk (*), the work should be done by a factory
authorized service representative.

Possible Cause

TEST

Product is cooked too long

 

No test available, operational condition

Failed thermostat

 

Check poles on thermostat for continuity

Failed element

 

Remove the wires and check for continuity
across the element

Failed heat contactor

 

Remove the wires from the contactor coil and
check for continuity across the contactor coil
connection

 

Ensure the contactor moveable points move
freely up and down

 

Check for 24 volts at the contactor coil when
the computer is running

*

Failed temperature sensor

 

Check resistance of sensor for accuracy

Failed pilot light

 

Check light for resistance

Failed transformer

 

Check coils on transformer for correct
resistance

CAUTION:

   

USE OF ANY REPLACEMENT PARTS OTHER THAN
THOSE SUPPLIED BY LANG OR THEIR AUTHORIZED
DISTRIBUTORS CAN CAUSE BODILY INJURY TO THE
OPERATOR AND DAMAGE TO THE EQUIPMENT AND
WILL VOID ALL WARRANTIES.

Summary of Contents for CLR36R-GB-S























Reviews: