manualshive.com logo in svg

LANDTEC GEM2000, Operating Manual

Share
Download
LANDTEC GEM2000 Operating Manual Download Page 16

OMGEMN1.41 

GEM2000 Range Gas Analysers 

Page 16

  

 Copyright 2009 Geotechnical Instruments (UK) Limited

 

4.2  Instrument Accessory Products 

Optional accessory and replacement parts may be purchased for the GEM2000 range from 
Geotechnical Instruments (UK) Limited direct.  Please refer to the website 

www.geotech.co.uk

 for further details on pricing and how to order. 

 

 

 

Ref 

Description 

Mfr Order 

Code 

A 

In-line Water Trap Housing (complete with tubing & filter) 

GAA1.8 

B 

 

C 

 

Water Trap with Barbed Filters (pack of 10) 
Water Trap with Barbed Filters (pack of 30) 
Water Trap Filters (pack of 10) 
Water Trap Filters (pack of 30) 

GA4.9 

GA4.9(30) 

GA4.2 

GA4.2(30) 

D 

Male Quick Coupling with Hose Barb (pack of 10) 

MC10 

E 

Sampling Tube 5m 

GA2.3 

F 

Inlet Port Filters (pack of 10) 
Inlet Port Filters (pack of 30) 

GA4.1 

GA4.1(30) 

G 

H

2

S Filters (Pack of 5) 

GA6.5 

H 

Regulator and Tubing for Calibration Gas  
Calibration Gas Canister : 
 
Please contact 

[email protected]

 for information on available 

concentrations. 

G1.1 

 
 

I 

Battery Charger 

GA3.9/S 

J 

Pitot Tube Kit 

PITOT 

K 

Soft Carry Case 

GA5.1 

L 

Gas Pod (various gas ranges available – please refer to website) 

 

M 

Hard Carry Case 

GA2.5 

N 

ATEX Certified Temperature Probe 

GA5.2 

O 

Anemometer 

GA5.4 

P 

Gas Analyser Manager (GAM) 
USB Lead 

GAM 

USBLEAD1 

Summary of Contents for GEM2000



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands