background image

1-2

7K555-2401

SAFETY INFORMATION

TABLE OF CONTENTS

Safety

NOTE

Investigation has shown that nearly 1/3 of all farm 
accidents are caused by careless use of machinery. 
Insist that all people working with you or for you abide by 
all safety instructions.

Understanding Safety Statements

You will find various types of safety information on the 
following pages and on the implement decals (signs) 
attached to the implement. This section explains their 
meaning.

NOTICE

CAUTION

WARNING

DANGER

DANGER

NOTE

You should read and understand the information 
contained in this manual and on the implement decals 
before you attempt to operate or maintain this equipment.

• Examine safety decals and be sure you have the 

correct safety decals for the implement.

 

See 

Figure 1-2.

• Order replacement decals through your Brillion dealer.
• Keep these signs clean so they can be observed 

readily. It is important to keep these decals cleaned 
more frequently than the implement. Wash with soap 
and water or a cleaning solution as required.

• Replace decals that become damaged or lost. Also, be 

sure that any new implement components installed 
during repair include decals which are assigned to 
them by the manufacturer.

• When applying decals to the implement, be sure to 

clean the surface to remove any dirt or residue. Where 
possible, sign placement should protect the sign from 
abrasion, damage, or obstruction from mud, dirt, oil 
etc.

DANGER

DANGER

Transporting Safety

IMPORTANT

It is the responsibility of the owner/operator to 
comply with all state and local laws.

• When transporting the implement on a road or 

highway, use adequate warning symbols, reflectors, 
lights and slow moving vehicle sign as required. Slow 
moving tractors and towed implements can create a 
hazard when driven on public roads. They are difficult 
to see, especially at night.

• Do not tow an implement that, when fully loaded, 

weighs more than 1.5 times the weight of the towing 
vehicle.

• Carry reflectors or flags to mark the tractor and 

implement in case of breakdown on the road.

• Do not transport at speeds over 20 MPH under good 

conditions. Never travel at a speed which does not 
allow adequate control of steering and stopping. 
Reduce speed if towed load is not equipped with 
brakes.

• Avoid sudden stops or turns because the weight of the 

implement may cause the operator to lose control of 
the tractor. Use a tractor heavier than the implement.

• Use caution when towing behind articulated steering 

tractors; fast or sharp turns may cause the implement 
to shift sideways.

• Keep clear of overhead power lines and other 

obstructions when transporting. Know the transport 
height and width of your implement. 

See 

“Specifications” in Chapter 5.

Special notice - read and throughly understand.

Proceed with caution. Failure to heed caution 
may cause injury to person or damage product.

Proceed with caution. Failure to heed warning will 
cause injury to person or damage product.

Proceed with extreme caution. Failure to heed 
notice will cause injury or death to person and/or 
damage product.

•   Do not allow anyone to ride on the tractor or 

implement. Riders could be struck by foreign 
objects or thrown from the implement.

•   Never allow children to operate equipment.
•   Keep bystanders away from implement during 

operation.

Summary of Contents for Brillion SS4

























































Reviews: