manualshive.com logo in svg

Landis+Gyr FOCUS kWh, Technical Manual

Share
Download
Landis+Gyr FOCUS kWh Technical Manual Download Page 22

 

5.

 

Overview of Electronic Hardware  

Delete “Optical” below

 

5.1.1.

 

LCD Display 

 

Figure 18 – Liquid Crystal Display 

The 

kWh FOCUS

 LCD shows the digital power indicator, nominal service voltage and various 

selectable metrics. 

5.1.2.

 

Display Scroll Sequence: 

The display scroll sequence is programmable at the factory or by the user with 

Focus Configuration 

Tool

.  The scroll sequence can consist of up to 16 individual displays.  The display choices are: 

•

 

+kWh 

•

 

-kWh 

•

 

NET kWh 

•

 

ADDED kWh (Security) 

•

 

Segment Check with Active DPI 

•

 

Line Voltage(s) 

Duplicate display choices are permitted as long as the total number of display choices in the scroll 
sequence does not exceed 16. 

The time of display can be programmed from 1 to 15 seconds in one-second increments. 

When internal meter errors occur, error codes will be added to the end of the scroll sequence.  

13

 

13

Summary of Contents for FOCUS kWh































Reviews:

No comments

Brands by name

Popular brands

Load more brands