background image

7

Safety

WARNING: Risk of injury. Hot 
surfaces can cause burns. Use 
only designated gripping areas of 
spray gun and wand. Do not place 
hands or feet on non-insulated 
areas of the pressure washer.

12. Transport/Repair with fuel tank EMPTY or with fuel 

shut-off valve OFF.

CAUTION: Hot discharge fluid. Do 
not touch or direct discharge 
stream at persons.

WARNING: This machine 
produces hot water and must 
have insulated components 
attached to protect the operator.

13. To reduce the risk of injury, close supervision is 

necessary when a machine is used near children. 
Do not allow children to operate the pressure 
washer. 

This machine must be attended during 

operation. 

WARNING: Grip cleaning wand 
securely with both hands before 
starting. Failure to do this could 
result in injury from a whipping 
wand.

14. Never make adjustments on 

machine while in operation.

15. Be certain all quick coupler fittings are secured 

before using pressure washer.

WARNING: High pressure 
developed by these machines will 
cause personal injury or 
equipment damage. Keep clear of 
nozzle. Use caution when oper-
ating. Do not direct discharge 
stream at people or animals, or 
severe injury or death will result. 

WARNING: Protect machine from 
freezing.

16. To keep machine in best 

operating conditions, it is 
important you protect machine 
from freezing. Failure to protect 
machine from freezing could 
cause malfunction of the 
machine and result in death, 
serious bodily injury, and/or 

property damage. Follow storage instructions 
specified in this manual.

17. Inlet water must be clean fresh water and no hotter 

then 90°F.

DANGER: Risk of asphyxiation. 
Running this product indoors can 
result in death due to carbon 
monoxide, a poison gas you 
cannot see or smell. Only use 
outdoors and far away from 
windows, doors, and openings 
or vents. Use this product only 
in a well ventilated area. 

18. Avoid installing machines in 

small areas or near exhaust fans. Adequate 
oxygen is needed for combustion or dangerous 
carbon monoxide will result.

19. Manufacturer will not be liable for any changes 

made to our standard machines or any compo-
nents not purchased from us.

20. The best insurance against an accident is precau-

tion and knowledge of the machine.

WARNING: Be extremely careful 
when using a ladder, scaffolding 
or any other relatively unstable 
location. The cleaning area 
should have adequate slopes and 
drainage to reduce the possibility 
of a fall due to slippery surfaces.

Landa MHP  Operator’s Manual   8.913-925.0 - T

WARNING

RISK OF INJURY. 

HOT SURFACES 

CAN CAUSE BURNS

CAUTION

HOT DISCHARGE FLUID:

DO NOT TOUCH OR

DIRECT DISCHARGE

STEAM AT PERSONS.

WARNING

RISK OF INJECTION 

OR SEVERE INJURY

TO PERSONS. KEEP 

CLEAR OF NOZZLE.

WARNING

PROCTECT FROM

FREEZING

WARNING

RISK OF INJURY

FROM FALLS WHEN

USING LADDER.

WARNING

TRIGGER GUN KICKS 

 BACK —  HOLD WITH 

        BOTH HANDS

RISK OF 

ASPHYXIATION. 

USE THIS PRODUCT 

ONLY IN A WELL 

VENTILATED AREA.

DANGER

Summary of Contents for MHP4 30324E















































Reviews: