background image

10

Operations

Assembly Instructions

STEP 1:

 Attach a 5/8" water supply 

hose to inlet connector. Minimum 
flow should be 6 or 10 gpm 
depending on model of machine.

STEP 4:

 Check engine and pump 

oil level by removing oil dipstick, 
making sure oil is on proper 
indicator marking. Oil should be 
visible one half way up sight glass 
located at the end of pump
 (SAE 10W-40 non-foaming).

STEP 2:

 Attach wand to spray gun 

using teflon tape on threads to 
prevent leakage. Attach swivel 
connector on discharge hose to 
spray gun using teflon tape on 
threads. Attach swivel connector on 
high pressure hose to spray gun 
using teflon tape on threads. 
Engage safety latch to prevent from 
triggering gun when inserting high 
pressure nozzle.

STEP 5:

 Fill red gasoline tank. Fill 

green fuel oil tank. Do not confuse 
gasoline and fuel oil (diesel) tanks. 
Keep proper fuel in proper tank.

STEP 3:

 Attach high pressure hose 

to discharge nipple using quick 
coupler. Lock coupler securely into 
place by pulling back coupler collar 
and inserting it into discharge 
nipple, then pushing collar forward 
to lock in place.

STEP 6:

 Install proper battery 

making sure that the red cable is 
attached to the positive terminal. 
Use a 12V Group 24 battery on all 
models except 4-40321 and 5-
35321E. These models use a U1 
30 amp garden tractor style battery.

Landa PGDC Operator’s Manual  8.916-596.0 - BF

Spray Wand

Safety 

Latch

Spray 

Gun

High Pressure 

Hose

GA

S

8.

91

6-27

4.0

DIESEL

8.932-

96

0.

0

High 

Pressure 

Hose

Discharge 

Nipple

GA

S

8.91

6-2

74.

0

DIESEL

8.932-960.0

Gasoline

Burner Fuel

Battery Installation

Due to Federal Regula-
tions concerning shipment 
of corrosive chemicals, 
batteries are not shipped 
with this machine.

Local purchase of battery will be the responsibility of 
the owner. Automotive type 12 Volt Group 24 battery is 
recommended for placement within the weather 
resistant box. Follow safety and installation instructions 
furnished with the battery.

Red Cable is attached to battery (+) positive terminal, 
black cable is connected to battery (-) negative 
terminal.

SHIELD 
EYES

 

EXPLOSIVE 
GASES 

CAN CAUSE 

BLINDNESS OR INJURY

  

NO

SPARKS
FLAMES
SMOKING

SULFURIC 
ACID

CAN CAUSE 
BLINDNESS OR 
SEVERE BURNS

FLUSH EYES 
IMMEDIATELY 
WITH WATER 

GET 
MEDICAL 
HELP 
FAST

KEEP OUT OF THE REACH OF CHILDREN. DO NOT TIP. KEEP VENT CAPS TIGHT AND LEVEL.

D A N G E R / P O I S O N

Black - Negative 
Terminal

Red + Positive 
Terminal

Black

Red

Summary of Contents for 1.110-049.0

























Reviews: