background image

Section 1: Options & Accessory Set-up 

SPL0548 & SPL0560 Snow Pusher 303-454M

11/9/20

18

Table of Contents

Hook-up BX80 Loader Arm Pin-on

DANGER

!

To avoid serious injury or death:  A crushing hazard exists 

while hooking-up and unhooking the implement. Do not allow 

anyone to stand between impelement and power machine 

while approaching or backing away from the implement. Do 

not operate lift and/or tilt controls while someone is near the 

power machine and/or implement.

WARNING

!

To avoid serious injury or death:  Check Kubota BX tractor 

hitch fit-up frequently to ensure the implement will not come 

loose and fall. The loader cylinder rod must be pinned to the 

implement’s center clevis with the hitch pin and hitch pin 

secured with a bolt and nut. The loader arms must be secured 

to the lower clevises with hitch pins and each hitch pin secured 

with a bolt, nut and snap ring.

Land Pride’s 

“BX80 Loader Arm Pin-on option”

 is 

required when hooking the Snow Pusher to BX80 Series 

Kubota tractors. See your nearest Land Pride dealer to 

order this option.

BX80 Loader Arm Pin-on Option #380-296A

Figure 1-12

Refer to Figure 1-12:

380-296A . . . . . . . . Option, BX80 Loader Arm Pin-on

Refer to Figure 1-11:

1. Unhook existing attachment from Kubota’s BX80 

front loader. Refer to Kubota’s LA344 Assembly or 

Operator’s Manual for detailed instructions.

2.

Refer to Figure 1-13 on page 19: 

Store existing hitch 

pins with the attachment. Keep snap rings (A) and flat 

washers (C). They will be needed to hook-up the 

Snow Pusher.

3. Check for and remove any debris in the hitch point 

areas before hooking-up the Snow Pusher.

74897

Bolts (#4) are for 
adjusting the BX80 
lift stand.

Hookup to BX80 Series Kubota Tractors

Figure 1-11

74934

Summary of Contents for SPL05 Series



































Reviews: