Land Pride SGC06, Operator'S Manual

Page: 13 / 34

Section 1: Assembly & Set-Up
SGC0660 Claw Grapple 380-164M 6/17/21
9
Table of Contents
Section 1: Assembly & Set-Up
Tractor Requirements
Tractor horsepower should be within the range noted
below. Tractors outside the horsepower range must not
be used.
Tractor Lift Capacity . . . . 1150 lbs (522 kg) Maximum
Hitch Options
. . . . . .Skid steer type quick attach that meets SAE
. . . . . . . . . . . . . . . . . . . . . . . Kubota B Series Hitch
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No Mount
Hydraulic Outlets:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Duplex outlet
. . . . . . . . or Third Function Valve Kit (See page 15)
Tractor Weight . . . . . . . . . . . . . . See Warnings Below
See “Australia Rated Operating Loads (ROL)” on
page 24.
WARNING
!
To avoid serious injury or death:
•
Consult your power machine Operator’s Manual for
operating capacity, lifting capacity, and operating
specifications. Exceeding rated capacities and
specifications can result in loss of control, roll-over or other
serious hazard.
•
Lightweight power machines may need weight added to the
rear to maintain steering control and prevent forward
tipping or side tipping caused by a heavy front load. Consult
your power machine Operator’s Manual to determine
proper weight requirements and maximum weight
limitations.
Torque Requirements
Refer to
“Torque Values Chart”
on page 27 to determine
correct torque values when tightening hardware.
IMPORTANT: Do not hitch SGC0660 grapple to a
skid steer. This grapple is not designed to handle
forces created by skid steers.
Before You Start
Make sure the intended tractor conforms to the
requirements provided on this page. Also, read and
understand this Operator’s Manual for your Claw
Grapple. An understanding of how it works will aid in its
assembly and set-up.
Go through the
“Pre-Assembly Checklist”
on this page
before assembling the Claw Grapple. To speed up your
assembly task and make the job safer, have all needed
parts and equipment readily at hand.
Hitch Plate Options
Grapples With Font Loader Hitch Plate
Claw grapples with this hitch plate will attach to a tractor
loader equipped with a front loader hitch plate. Follow all
instructions in this Operator’s Manual except instructions
specifically provided for the Kubota B Series Hitch.
Grapples With Kubota B Series Hitch Plate
Claw grapples with this mount fit the Kubota B Series
front loader hitch. Follow all instructions in this Operator’s
Manual except instructions specifically provided for the
front loader hitch plate.
Grapples With A Blank Hitch Plate
Claw grapples with a blank hitch plate option will allow
the customer to install a hitch plate that fits their power
unit. Follow all instructions provided in this Operator’s
Manual. Use hook-up and unhooking instructions in this
manual and your equipment’s Operator’s Manual to know
how best to hook-up and unhook the claw grapple.
Pre-Assembly Checklist

Check Ref.
Have a forklift or loader with properly sized chains capable of
lifting the equipment on hand.
Make sure all major components and loose
parts are shipped with the attachment.
Assembly
& Set-up
Double check to make sure all parts, fasteners,
and pins are installed in the correct location.
Refer to the Parts Manual if unsure.
Parts Manual
380-164P
Make sure working parts move freely, bolts are
tight & cotter pins are spread.
Operator’s
Manual
Make sure all safety labels are correctly
located and legible. Replace if damaged.
Page 6