background image

1

Important Safety Information

2/11/21

SB1051, SB1064, SB1574, & SB2584 with S/N 881640- Snow Blowers   370-027M

Table of Contents

Important Safety Information

s

These are common practices that may or may not be applicable to the products described in 

this manual.

Safety at All Times

Thoroughly read and understand 

the instructions given in this 

manual before operation. Refer to 

the “Safety Label” section, read all 

instructions noted on them.
Do not allow anyone to operate 

this equipment who has not fully 

read and comprehended this 

manual and who has not been 

properly trained in the safe 

operation of the equipment.

s

The operator must not use drugs 

or alcohol as they can change the 

alertness or coordination of that 

person while operating equipment. 

The operator should, if taking 

over-the-counter drugs, seek 

medical advice on whether he/she 

can safely operate the equipment.

s

Operator should be familiar with all 

functions of the unit.

s

Operate controls from the driver’s 

seat only. Never operate controls 

from the ground.

s

Make sure all guards and shields 

are in place and secured before 

operating implement.

s

Keep all bystanders away from 

equipment and work area. 

s

Do not leave tractor or implement 

unattended with engine running.

s

Dismounting from a moving tractor 

can cause serious injury or death.

s

Do not allow anyone to stand 

between tractor and implement 

while backing up to implement.

s

Keep hands, feet, and clothing 

away from power-driven parts.

s

Watch out for fences, trees, rocks, 

wires, etc., while operating and 

transporting implement.

s

Turning tractor too tight may cause 

hitched machinery to ride up on 

wheels. This could result in injury 

or equipment damage.

Look For The Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a 

potential hazard to personal safety involved and extra 

safety precaution must be taken. When you see this 

symbol, be alert, and carefully read the message that 

follows it. In addition to design and configuration of 

equipment, hazard control, and accident prevention are 

dependent upon the awareness, concern, prudence, and 

proper training of personnel involved in the operation, 

transport, maintenance, and storage of equipment.

SB10 Series

SB25 Series

SB15 Series

Manual QR Locator

The QR (Quick Reference) codes below will take you to the Parts Manual for this 

equipment. Download the appropriate App on your camera phone, open the 

App, point your phone on the QR code, and take a picture.

Dealer QR Locator

The QR code below will link you 

to available dealers for Land 

Pride products.

!

Be Aware of 

Signal Words

A Signal word designates a degree or 

level of hazard seriousness. The 

signal words are:

Indicates an imminently hazardous 

situation which, if not avoided, will 

result in death or serious injury. This 

signal word is limited to the most 

extreme situations, typically for 

machine components that, for 

functional purposes, cannot be guarded.

Indicates a potentially hazardous 

situation which, if not avoided, could 

result in death or serious injury, and 

includes hazards that are exposed 

when guards are removed. It may also 

be used to alert against unsafe 

practices.

Indicates a potentially hazardous 

situation which, if not avoided, may 

result in minor or moderate injury. It 

may also be used to alert against 

unsafe practices.

!

WARNING

!

CAUTION

!

DANGER

For Your Protection

s

Thoroughly read and understand 

the “Safety Label” section, read 

all instructions noted on them.

OFF

REMOVE

Tractor Shutdown & Storage

s

If engaged, disengage PTO.

s

Lower attached implement to 

ground, put tractor in park or set 

park brake, turn off engine, and 

remove switch key to prevent 

unauthorized starting.

s

Wait for all components to come to 

a complete stop before leaving the 

operator’s seat.

s

Detach and store implement in an 

area where children normally do 

not play. Secure implement 

using blocks 

and supports.

Summary of Contents for SB10 Series











































Reviews: