background image

25

Section 5: Operating Instructions

2/11/21

SB1051, SB1064, SB1574, & SB2584 with S/N 881640- Snow Blowers   370-027M

Table of Contents

!

WARNING

Do not operate Snow Blower with loose pins, bolts, and nuts. 

Loose hardware can result in a serious breakdown causing 

bodily injury or death.

!

WARNING

Never operate Snow Blower without good visibility and light. 

Use a tractor equipped with a cab to make seeing easier.

!

WARNING

Always dress to stay warm in cold weather. Use a tractor 

equipped with a cab to help stay warm and to protect against 

cold blowing snow. Never allow your body or extremities to 

become too cold. Go inside to warm-up if you are getting too 

cold. 

!

WARNING

Dress properly for the job. Do not wear loose fitting clothing 

that could get caught in moving parts and be careful with long 

hair around moving parts. Wear footwear that will improve 

footing on slippery surfaces. Always be sure of your footing 

and keep a firm hold on handles. Walk, never run.

!

WARNING

The chute can rotate 360

o

. Never rotate chute to throw snow 

at the tractor. The Snow Blower is capable of picking up solid 

objects and discharging them at high speeds causing serious 

bodily injury or death.

!

WARNING

Keep people and animals away while removing snow. Never 

operate Snow Blower with chute throwing snow towards 

animals or people. The Snow Blower is capable of picking up 

large solid objects and discharging them at high speeds 

causing serious bodily injury or death.

!

WARNING

Always be aware of pedestrians and vehicle traffic. Move 

snow during low-traffic hours. Always exercise safety, 

courtesy, and common sense.

!

WARNING

If required, use back-up alarm to warn others you are 

backing-up. Always comply with all federal, state, and local 

laws.

!

WARNING

Always travel removing snow at a speed that allows the 

operator to be in control at all times and always be ready to 

make emergency stops. Snow removal speed will vary 

depending on depth of snow, how wet the snow is, and how 

tight the snow is compacted.

!

WARNING

Never pile snow where it obstructs visibility of traffic. Never 

pile snow near fire hydrants, mailboxes, water drains, shut-off 

valves, electrical boxes, handicap, and parking areas. 

!

WARNING

Beware of obstacles along side the tractor while making turns 

backing-up removing snow. Never swing front of tractor or 

tractor mounted front loader into fire hydrants mail boxes, 

buildings, vehicles, fences, trees, or other standing obstacles.

!

WARNING

Do not operate Snow Blower with loose pins, bolts, and nuts. 

Loose hardware can result in a serious breakdown causing 

bodily injury or death.

!

WARNING

Never remove snow that has been plowed. Blow only fresh 

snow that has not been disturbed. Plowed snow contains 

foreign particles such as dirt and rocks that can cause serious 

bodily injury or death. 

!

WARNING

Do not operate Snow Blower with auger flighting or impeller 

blades that are broken or bent making contact with the 

housing. Broken or bent flighting and blades can break loose 

from the Snow Blower at high speeds causing serious injury or 

death.

!

WARNING

Do not use Snow Blower as a working platform. The Snow 

Blower is not properly designed or guarded for this use and 

could cause a serious injury or death.

!

WARNING

Never allow riders including children on the tractor or Snow 

Blower. They can fall and be ran over causing serious injury 

or death.

!

WARNING

Do not use Snow Blower to lift or carry objects; to pull fence 

posts, stumps or other objects; or to tow other equipment. 

Doing so can damage the Snow Blower, cause serious bodily 

injury or death.

IMPORTANT: 

Check driveline coupling bolt at the 

gearbox input shaft daily to verify if it is tight and 

yoke is secured to gearbox input shaft. Check 

driveline yoke at tractor PTO shaft to verify pull 

collar is properly locked to PTO shaft.

Summary of Contents for SB10 Series











































Reviews: