manualshive.com logo in svg

Land Pride Rear Blades RBT45108, Operator'S Manual

Share
Download
Land Pride Rear Blades RBT45108 Operator'S Manual Download Page 19

Section 2: Set-Up of Accessories 

RBT4596 & RBT45108 Rear Blades 301-205M

1/13/21

15

Table of Contents

Hydraulically Controlled Gauge Wheel

Figure 2-2

24996

Customer to supply Quick 
Disconnect Couplings.

Ratchet Jack Set-Up

1. Attach ratchet jack (#19) to the mounting lugs on the 

gauge wheel arm (#3) and mounting bracket (#11) 

with two 1" clevis pins (#20). Secure pins with hair pin 

cotters (#21).

Hydraulic Cylinder Set-Up

1. Position hydraulic cylinder (#15) with ports on top as 

shown. Thread 90 degree elbows (#13) into the two 

ports and tighten.

2. Screw 116" long hydraulic hoses (#14) to the elbows 

and tighten. 

3. Thread hydraulic couplings (#18) to the other end of 

hydraulic hoses and tighten. (Customer to supply 

quick disconnect hydraulic couplings.) 

4. Attach hydraulic cylinder to the lugs on the gauge 

wheel with two 1" clevis pins (#17). Make sure 

hydraulic ports are positioned on top and cylinder 

base is located to the front as shown.

5. Secure clevis pins with hair pin cotters (#16).
6. Route hoses through the hose brackets located on 

the top of the main frame and right side of the front 

hitch. Connect hoses to tractor's hydraulic system.

IMPORTANT: 

Attach cylinder base to the front 

mounting lug. The base will interfere with the gauge 

wheel arm if attached to the rear mounting lug.

Gauge Wheel

Kit Bundles

301-225A . . . . . . HYDRAULIC SINGLE GAUGE WHEEL
301-236A . . . . . . . .HYDRAULIC DUAL GAUGE WHEEL
301-281A . . . . . . . . .MANUAL SINGLE GAUGE WHEEL
301-282A . . . . . . . . . .  MANUAL DUAL GAUGE WHEEL

Refer to Figure 2-2::

1. Attach gauge wheel mounting bracket (#11) to Rear 

Blade frame with two 3/4"-10 x 10 1/2" GR5 hex head 

bolts (#8) and 3/4" hex nuts (#10). Tighten nuts to 

correct torque.

2. Insert gauge wheel hitch tube (#9) in gauge wheel 

arm (#3).

3. Attach gauge wheel arm (#3) to mounting 

bracket (#11) with 3/4"-10 x 10 1/2" GR5 hex head 

bolt (#8) and 3/4" hex nut (#10). Tighten nut to correct 

torque.

4. Insert gauge wheel caster assembly (single wheel 

caster #1) or (dual wheel caster #2) in gauge wheel 

arm (#3) and retainer washer (#4). Secure caster 

assembly with 1/2" x 2 1/2" long roll pin (#5).

5. Attach center floating link (#12) to the front hitch with 

1 1/4" x 1 3/4" hitch pin (#7). Secure with hair pin 

cotter (#6).

Summary of Contents for Rear Blades RBT45108







































Reviews:

No comments

Brands by name

Popular brands

Load more brands