Land Pride RCF3010 Operator'S Manual Download Page 23

Page: 23 / 76

Section 1: Assembly & Set-Up

Table of Contents

RCF3096, RCF3010, & RCFM3010 Rotary Cutters 326-566M

11/8/18

Hydraulic Hook-up Option (3-Point)

Thread hydraulic hoses (#8 & #9) through spring
hose loop (#3) and attach to tractor duplex outlet.

2. Hydraulic cylinder should extend when pushing

control lever. Reverse hook-up if cylinder retracts.

3. Continue with

“Check Driveline Clearance”

page 27.

Add 7/16" Dia. Hitch Pin Hole

Figure 1-12

Hitch Pin Modification (3-Point & Semi)

Refer to Figure 1-12:

A 7/16" diameter hole must be drilled 1 3/16" from end of
hitch pin (#1) as shown to receive linchpin (#3) or roll
pin (#4). Make sure the hole is straight, vertical, and
passes through the center of the hitch pin diameter.

Linchpin #3 is used to securing Cat. II lower 3-point arms
outside of the cutter hitch plates.

The Cat. II quick hitch attaches to adapter bushing (#5)
outside the cutter hitch plates. Secure bushing (#5) to
hitch pin (#1) with roll pin (#4).

Item Pt. No.

Description

805-485C

PIN HTCH C1-C2 10.18 L

805-088C

PIN, HAIR COTTER 3/16 WIRE DIA

805-103C

PIN LINCH 7/16 X 1 3/4

805-393C

PIN ROLL 7/16 X 1 3/8 PLT

890-938C

ADAPTER QH CAT II LWR 3PT

39673

NOTE:

Linchpin (#3), adapter bushing (#5), and roll

pin (#4) are accessories and can be purchased from
your nearest Land Pride dealer.

Summary of Contents for RCF3010













































































Search results

Summary of Contents for RCF3010

Reviews:

Related manuals for RCF3010

Brands by name

Popular brands

Land Pride RCF3010, Operator'S Manual

Search results

Summary of Contents for RCF3010

Reviews:

Related manuals for RCF3010

Brands by name

Popular brands