Land Pride RCF3010 Operator'S Manual Download Page 25 | Manualshive

Page: 25 / 76

background image

Section 1: Assembly & Set-Up

Table of Contents

RCF3096, RCF3010, & RCFM3010 Rotary Cutters 326-566M

11/8/18

21

Semi-Mount Driveline Installation

Figure 1-14

Driveline Installation (Semi-Mount)

Refer to Figure 1-14:

DANGER

!

To avoid serious injury or death:

Make certain driveline yokes are securely fastened at each
end. A loose yoke can work free allowing the driveline to
rotate uncontrollably causing implement damage and bodily
injury or death to anyone nearby.

1.

Remove rubber protective sleeve (#4) from gearbox
input shaft and discard.

2. Unsnap one end of gearbox shield access doors (#6)

and rotate doors open.

3. Remove conical dog pin or bolts (#1), washer(s) (#3),

and nut(s) (#2) from slip-clutch end of driveline (#5).

4. Slide slip-clutch end of driveline (#5) onto gearbox

input shaft. Make certain that the slip-clutch is fully
onto the shaft splines.

5. Attach slip-clutch end of driveline to gearbox input

shaft with existing conical dog pin or bolts (#1), flat
washer(s) (#3), and nut(s) (#2). Tighten conical dog
pin or bolts (#1) on slip-clutch to 45-50 ft-lb torque.

6. Push/pull on driveline yoke to ensure it is securely

fastened to the gearbox shaft.

7.

Rotate access doors (#6) closed and snap in place.

35045

IMPORTANT:

The drivelines must be lubricated

before putting them into service. Refer to

“Lubrication Points”

NOTE:

If preferred, the front guards may be

assembled first. See

“Assembly of Optional

Equipment”

on page 34 for front guard instructions.

Semi-Mount Assembly & Set-Up

The following pages are Assembly & Set-Up Instructions
for Semi-Mount cutters. See

“3-Point Assembly & Set-

“Pull-Type Assembly & Set-Up”

Spring Hose Loop Assembly

Figure 1-13

Spring Hose Loop For Semi-Mount

Refer to Figure 1-13:

1.

Attach mounting bracket (#1) with 3/4"-10 x 1 1/2"
GR5 cap screw (#3) and locknut (#4) to the right-hand
clevis as shown. Tighten nut to the correct torque.

2. Attach spring hose loop (#6) to mounting bracket (#1)

with 3/8"-16 x 1" GR5 cap screw (#2), flat
washer (#5), and locknut (#4). Tighten nut to the
correct torque.

35006

«
...
23
24
25
26
27
...
»

Summary of Contents for RCF3010













































































Reviews:

No comments

Related manuals for RCF3010

MASTER FF 180-2

Brand: Würth Pages: 96

Brand: Simplex Pages: 8

Brand: Daewoo Pages: 12

Brand: QEP Pages: 8

Brand: Logan Pages: 8

Brand: Logan Pages: 12

HT-2556 D, HT-2576 E

Brand: Dolmar Pages: 88

Brand: Stiga Pages: 458

Brand: D-CUT Pages: 9

Brand: Masport Pages: 28

Brand: Becx Machines Pages: 27

Brand: Dace Technologies Pages: 52

Brand: Tanaka Pages: 18

NORTON clipper TR 252

Brand: SAINT-GOBAIN Pages: 24

Brand: Land Pride Pages: 64

Brand: PAPILLON Pages: 42

Brand: Tanaka Pages: 56

Brand: Gastroback Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands