background image

34

RC5010 & RC6010 (540 RPM) and RCM5010 & RCM6010 (1000 RPM) Rotary Cutters   318-128M

8/28/08

Land Pride

Section 5: Maintenance & Lubrication

Table of Contents

Divider Box

Type of Lubrication: 80-90W EP

Quantity = As required

NOTE: Do not overfill! Cutter should be level when
checking oil. If, for any reason, all oil has been removed
from gearbox, refill to level plug and allow air to bleed up
from lower cavity, then recheck.

14051

8

Hrs

Gearbox

Make sure wings are down. Unscrew top vent plug in
gearbox to remove dipstick. Wipe excess oil from dipstick
and screw it back into the plug hole. Remove dipstick again
and check oil level mark on dipstick. If low, fill through top
plug hole in gearbox with EP90 oil until oil reaches full mark
on dipstick. Reinstall vent plug with dipstick and tighten.

Take your gearbox to a Land Pride dealer if it requires
service.

Type of Lubrication: EP90 Oil

Quantity = Fill until oil reaches full mark on dipstick.

IMPORTANT: Do not overfill! Level cutter and wait
for gearbox oil to cool before checking. An unlevel
cutter or a gearbox with hot oil will not show correct
oil level on the dipstick.

8

Hrs

23563

Intermediate Driveline Joints

Type of Lubrication: Multi-purpose Grease

8

Hrs

23582

IMPORTANT: Your cutter is shipped with the
gearbox vent plug/dipstick installed in the
gearbox. Please see your Land Pride dealer if the
vent plug/dipstick was not included.

Oil Level Plug

Oil Drain Plug

23603

Oil Fill Plug

Summary of Contents for RC5010















































Reviews: