Land Pride RC3620, Operator'S Manual

Page: 35 / 64

Section 3: Operating Instructions
RC3620 & RCM3620 Rotary Cuters 330-841M 9/25/18
31
Table of Contents
•
Perform scheduled maintenance. Check for loose
hardware, missing parts, broken parts, structural cracks,
and excessive wear. Make repairs before putting implement
back into service. Serious breakdowns can result in injury
or death.
•
Never carry riders on the implement or tractor. Riders can
obstruct the operator’s view, interfere with control of the
equipment, be pinched by moving components, become
entangled in rotating components, be struck by objects, be
thrown or fall from the equipment, etc.
•
Always shut tractor down using “Tractor Shutdown
Procedure” provided in this manual before dismounting
tractor.
•
Do not raise the wing off the ground when mowing across
an incline. The weight of the wing will increase the risk of a
rollover.
•
Operate only power machines equipped with a certified
Roll-Over Protective Structure (ROPS) and seat belt. Keep
folding ROPS in the “locked up” position when
appropriate. If ROPS is in the locked up position, fasten seat
belt snugly and securely to help protect against serious
injury or death from falling and machine overturn.
•
Clear area to be cut of debris and other unforeseen
removable objects before cutting. Mark non-removable
hazards such as tree stumps, post stubs, protruding objects,
rocks, drop-offs, holes, etc. with a visible flag.
•
Watch while making tight turns to ensure that the rear
tractor tires and lower 3-point arms do not make contact
with cutter hitch, driveline or deck. Keep lower 3-point
arms raised at all times when hitched to a pull-type cutter.
•
Wait for blades to come to a complete stop before accessing
blade bolts through blade bolt access hole.
•
Do not use implement to lift objects; to pull objects such as
fence posts, stumps, etc; or to push objects. The unit is not
designed or guarded for these uses.
•
Do not use implement to tow other equipment unless it is
designed with a tow hitch. Doing so can result in loss of
control and damage the equipment.
•
Do not operate a cutter with a hitch or hitch pin that is
excessively worn, bent, broken, or has structural cracks.
The hitch and/or hitch pin can break apart separating cutter
from tractor.
•
Do not use a power take-off adapter. The adapter will
increase strain on the tractor’s power take-off shaft causing
possible damage to shaft and driveline. It will also defeat
the purpose of the tractor’s power take-off shield.
•
•
Avoid catching hydraulic hoses on brush, posts, tree limbs,
and other protrusions that could damage and/or break them.
•
Buildup of debris around moving components and
gearboxes is a fire hazard. Keep rotating parts and
gearboxes free from debris to avoid serious injury and
property damage.
•
Improper oil level can cause bearing failure and be a fire
hazard. Maintain proper gearbox oil level to avoid serious
injury and property damage.
•
Do not exceed rated cutting capacity of your cutter. See
specifications & capacities for specified cutting capacity.
Exceeding rated cutting capacity can damage drive
components, cutter blades, and deck components.
CAUTION
!
To avoid minor or moderate injury: Some tractors are
equipped with two power take-off speeds. Be certain your
tractor’s power take-off is set at the implement’s rated power
take-off speed or equipment breakage may result. RC models
are rated for 540 rpm and RCM models are rated for 1000
rpm.
Standard Conventional U-Joint Driveline
Figure 3-1
Constant Velocity (CV) Driveline
Figure 3-2
Avoid Extreme Turning Angles
Refer to Figure 3-1 & Figure 3-2:
Plan your field cutting to minimize number of turns,
especially extreme turning angles. Avoid tractor-to-cutter
turning angles that exceeds driveline maximum turning
angle. If the turn cannot be avoided, disengage tractor
power take-off and wait for the driveline to stop rotating
before making the turn.
•
Standard Conventional Driveline:
Maximum turning angle = 35
o
.
•
Constant Velocity Driveline:
Maximum turning angle = 80
o
.
IMPORTANT: Maintain correct power take-off speed.
Loss of power take-off speed will allow blades to
swing back and result in ragged, uneven cutting.
IMPORTANT: If wing driveline profile is bent or
twisted, disconnect that driveline from the wing
gearbox before folding the wing up. This will protect
both the wing and divider gearbox. Repair driveline
before putting cutter back into service.
11934
20795