Land Pride RC2512 Series Operator'S Manual Download Page 53

Page: 53 / 60

Section 6: Specifications & Capacities

10/7/21

RC2512 Series 2 S/N Rotary Cutters 330-725M

Table of Contents

Section 6: Specifications & Capacities

RC2512 Series 2

Specifications & Capacities

Tractor horsepower

40-100 hp (30-75 kW)

Gearbox horsepower

Splitter

Center & wings

160 hp (119 kW)
100 hp (75 kW)

Gearbox shafts

Input shaft

Output shaft

1 3/8" (3.5 cm) 6 Spline
1 1/2" (3.8 cm)

Gearbox capacity & lubrication

Splitter

Center & wings

4.5 pints (2.13 L) of gear lube 80-90W EP
4 pints (1.89 L) of gear lube 80-90W EP

Cutting capacity

1 1/2" (3.8 cm)

Hitch weight

793 lbs (359.7 kg)

Machine weight

2,540 lbs (1152.1 kg)

Blade tip speed At 540 rpm

Center Blades = 16,500 FPM (83.8 mps)

Wing Blades = 16,000 FPM (81.3 mps)

Hitch types

LP Performance hitch and swivel hitch

Hitch jack

Standard (2,000 lbs) (907.2 kg)

Cutting width
Overall cutter width
Minimum transport width

12'-0" (3.66 m)
12'-7" (3.84 m)
7'-11" (2.41 m) With front cutting blade 1 1/2" (3.8 cm) off the ground.

Overall length

13'-3" (4.04 m)

Deck height

11" (27.9 cm)

Cutting height

1 1/2" to 12" (3.8 cm to 30.5 cm)

Lift hydraulics

2 1/2" bore x 8" stroke hydraulic cylinder, hoses, fittings and stroke control spacers

Wing folding hydraulics

2" bore x 8" stroke hydraulic cylinders, hoses, and fittings

Wing flex while operating

Max. 20

down, can float up as needed as long as the wheel(s) are still on the ground.

Wing transport protection

Wing transport locks

Deck material

10 Gauge (3.4 mm) deck

Side skirt material

3/16" (5 mm) Plate

Skid shoes

Wing deck: 1 replaceable per wing
Center deck: 2 replaceable shoes

Blade rotation

Left wing

Center deck

Right wing

Counterclockwise
Counterclockwise
Clockwise

Blades - 6 (2 per deck)

1/2" x 3" (1.3 cm x 7.6 cm) Heat treated free swinging alloy Steel with up lift

Blade overlap

6" (15.2 cm)

Blade bolt

Keyed with hardened flat washer and locknut

Stump jumper / blade holder

10 Gauge (3.4 mm) round dish shaped pan, reinforced
with 1" x 3 1/2" (2.5 cm x 8.9 cm) blade bar

Front & rear guards

Single chain

Input driveline

Category 4 with constant velocity u-joint

Intermediate & wing drivelines

Category 3 with slip-clutch

Wheels

20.5" x 6.75" x 10" (52.1 cm x 17.1 cm x 25.4 cm) used aircraft tires
or 21" (53.3 cm) laminated wheels

Number of wheels

4 - Wheels: 2 on transport axle and one on each wing axle

Transport axle

Spring-cushioned lift cylinder

Signal lights
7 Pin connector

LED
SAE J560 pin configuration

Hubs

Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" (4.4 cm) shafts.

Summary of Contents for RC2512 Series





























































Search results

Summary of Contents for RC2512 Series

Reviews:

Brands by name

Popular brands

Land Pride RC2512 Series, Operator'S Manual

Search results

Summary of Contents for RC2512 Series

Reviews:

Brands by name

Popular brands