23
Section 2: Operating Instructions
MPS2607, MPS2609, & MPS2611 Multi-Purpose Seeder 329-301M
Table of Contents
8/8/23
Enhance Module Wire Connections For LED Lights
Figure 2-2
Check LED Lights
Refer to Figure 2-2:
Check LED lights to make certain they are operating
correctly.
1.
It is best to have a second person available to verify
the lights are operating correctly. Start tractor and
operate lights as follows:
a. Turn on head lights to verify red lights illuminate.
b. Turn on flasher lights to verify amber light are
blinking on and off.
2.
If lights did not operate properly, recheck hook-up of
wire harness (#1, #2, & #4) to enhance module (#3).
•
Make sure connector (#1D) with a red wire is
connected to the right-hand wire harness (#1).
•
Make sure connector (#2D) with a yellow wire is
connected to the left-hand wire harness (#2).
•
Make sure connector (#3B) on the lead wire
harness (#4) is connected to connector (#3A) on
enhancer module (#3).
3.
Check wire harness routing to make sure wires will
not be pinched as the seeder is raised and lowered.
4.
Add cable ties to wire harness (#1, #2, & #4) as
needed to secure them in place.
70482
IMPORTANT:
Connectors on wire harness (#1 & #2)
are labeled “Light” on one end and “Enhancer” on
the other end. Ends labeled “Light” connect to the
LED lights. Ends labeled “Enhancer” connect to
enhance module (#3).
IMPORTANT:
Connector (#1D) has a Red wire and
connects to wire harness (#1) on the right side of the
implement. Connector (#2D) has a yellow wire and
connects to wire harness (#2) on the left side of the
implement.
Check Tractor Clearance
Refer to Figure 2-1 on page 22:
1.
Shut tractor down properly. See
“Tractor Shutdown
Procedure”
on page 21.
2.
Adjust front rollers all the way forward. Refer to
“Front Spike Roller Angle”
on page 36 for detailed
instructions.
3.
From the tractor seat, slowly raise and lower seeder
with hydraulic 3-point lift while watching for drawbar
clearance, tire clearance, and 3-point clearance.
4.
If drawbar interferes, shut tractor down properly.
5.
Move drawbar back, to one side, or remove drawbar.
Unhook 3-Point Seeder
Refer to Figure 2-1 on page 22:
1.
Clean seedboxes, seed cups, and drop tubes before
unhooking seeder. Refer to
“Long-Term Storage”
on page 62.
2.
Park tractor and seeder on level, solid ground.
Preferably store seeder inside a shed to keep
moisture away from the seedboxes.
3.
Shut tractor down before dismounting. Refer to
“Tractor Shutdown Procedure”
on page 21.
4.
Chock front and back rollers to keep unit from
moving.
5.
Disconnect lead wire harness (#4). Coil harness up
and store on the seeder frame with plug end hanging
down to keep moisture out.
6.
Remove hitch pin keeper (#5) and hitch pin (#3).
Store center link in tractor storage hook.
7.
Reinstall hitch pin (#3) and keeper (#5) in the
seeder’s upper 3-point center clevis.
8.
Remove linchpins (#2) and hitch pins (#1).
9.
Start tractor and drive forward several feet and then
shut tractor down properly before dismounting. Refer
to
“Tractor Shutdown Procedure”
on page 21.
10. Replace hitch pins (#1) in the seeder’s lower 3-point
clevises. Secure with linchpin (#2).
11.
Refer to
Figure 2-7 on page 27:
Remove slow
moving vehicle sign (#5) from the back of the seeder
and insert it in the mounting socket on the back of the
tractor.
