background image

Section 5: Maintenance & Lubrication 

Table of Contents

AFM4522 All-Flex Grooming Mower 315-360M

11/18/21

38

Refer to Figure 5-4:

2. Remove blades by grasping the blade end (#1) with a 

rag or thick padded glove while loosening the blade 

mounting bolt (#4). 

3. Remove center blade bolt (#4) and two outside blade 

bar bolts (#5) from bottom of blade to be replaced.

WARNING

!

To avoid serious injury or death:  

Replace mower blades with genuine Land Pride blades 

only.

See Figure 5-4. If blade bar (#2) has been removed from 

spindle shaft (#3), apply “Loctite 243” to external threads 

on spindle shaft (#3) and threads on the center spindle bolt 

(#4) before reinstalling existing or new blade bar. Without 

Loctite 243, the startup torque of unit can let blade assembly 

unscrew thus dropping it from the spindle/mower. 

Blade & Blade Bar Removal

Figure 5-4

4. Reinstall blade, blade washer, and bolt. Care should 

be taken when installing the blade bolt to not get it 

cross threaded and to know if the bolt is right-hand or 

left-hand. Do not exceed 55 ft.-lb (75 N· m) of torque 

on bolt.

IMPORTANT: 

Always install blade with cutting edge 

facing direction of rotation and wing tips pointing up.

18952

5. Reinstall the two outside bolts. Tighten bolts to the 

correct torque listed in the 

“Torque Values Chart for 

Common Bolt Sizes” 

on page 52.

Blade Sharpening

WARNING

!

To avoid serious injury or death:  
Wear eye protection and gloves while inspecting, removing, 

sharpening, and replacing a blade.

1. A cutting blade should be replaced or sharpened if it 

is dull or nicked. 

2. Clean blade washer and blade mounting surface 

before installing a new blade. Also clean the old 

blade if you plan to sharpen it for reuse.

Refer to Figure 5-5:

3. Maintain sharpness by grinding only the top of the 

cutting edge at the same bevel as the original edge.

Blade Sharpening

Figure 5-5

Refer to Figure 5-6:

4. Check blade balance by positioning the blade 

horizontally on a nail or shaft through the blade’s 

center hole. If either end of blade rotates downward, 

grind (remove) metal on that end until blade will 

balance horizontally on the nail. The blade is 

properly balanced when neither end drops. Balance 

of a blade is generally maintained by removing an 

equal amount of material from each end of the blade.

Blade Balancing

Figure 5-6

NOTE:  

Care should be taken to not remove more 

material than necessary when sharpening blades.

19327

NAIL OR SHAFT

HORIZONTAL

19046

Summary of Contents for AFM4522



























































Reviews: