background image

6

CONTINUED ON NEXT PAGE

Lancer PN: 28-1005/01

8.  Feed the power wires (blue and brown) of the LED 

Driver through the opening in the Control Box.

9.  Plug the positive (blue) and the negative (brown) wires 

of the LED Driver into their appropriate positions on 

the central connection terminal.

10. Re-attach the control box cover.
11.  Remove existing wiring diagram from control box  

cover and replace with new wiring diagram included 

with kit (06-4002).

12. Connect the LED Driver Jumper Wire to the LED  

Driver then, using the adhesive clips provided, route 

the jumper wire to the top left side of the unit.

Jumper wire not needed for 22” configurations.  

NOTE

If a water button installation is required, refer to the 

water button installation instructions (Lancer PN: 28-

3016) before going on to step 13. 

NOTE

13. Secure the Light Panel Assembly in place by inserting  

the connection tabs of the Light Panel Assembly into 

the slots, horizontally, on either side of the  

Merchandiser Frame Assembly.

14. Once the connection tabs are inserted into the slots, 

pull down on the Light Panel assembly to secure the 

connection tabs into the slots on the frame assembly.

15. Plug the LED Driver cable, routed in Step 12, to the 

LED Light Panel Jumper Cable.

16. Plug-in the unit to test light panel operation before 

completing merchandiser assembly.

Summary of Contents for 82-5248











Reviews: