Lance Truck Camper, Owner'S Manual

Page: 54 / 112

54
50
2. TV hook-up
3. Antenna/cable switch
4. Antenna booster light
To use the TV antenna, turn “ON” the switch located on
the TV jack (Item 3). A red light will show on the
indicating the antenna booster is powered. There will
be a small continual 12-volt current drain as long as
the switch is on. Turning the switch “OFF” changes the
TV jack from antenna operation to park cable and
ceases the current draw.
NOTE: The 12-volt outlet is intended for a TV only and
rated for 7.5 amps. DO NOT USE FOR HIGHER
RATED APPLIANCES.
TV ANTENNA/SATELLITE DISH COMBO
Units equipped with a satellite dish have an additional
outlet located next to the TV jack. The satellite receiver
will connect to this outlet. The system also comes with
an Elevation Sensor. The satellite receiver manual will
give you the correct elevation to set your dish to. Press
the button on the Digital Display. If the antenna is in the
travel position, the display will show “LL” for Low Limit.
“HL” for High Limit will show when the dish is in the UP
position. A 9-volt battery located on the back side of
the display powers the Elevation Sensor. Crank the
elevation handle to raise the antenna. Stop cranking
when the readout displays the correct elevation for
your location. Rotate the antenna VERY SLOWLY until
the correct satellite signal is acquired. Before installing
and connecting a satellite receiving system, be sure
you are familiar with the components you intend to
install, other hardware or components required, and
how they are designed to work together. Always refer
to the component manufacturer’s installation/operation
information before installing or operating a satellite
system in your
camper.
For operation of the TV or satellite antennas, see their
operation manuals located in your Owner’ Information
Package.
SATELLITE DISH-SELF POSITIONING
STEREO/SPEAKER PRE-WIRE
All Lance campers are pre-wired for a future stereo
system. The speakers or speaker wiring are located in
the ceiling, two in the cabover area and two over the
dinette in the main ceiling. Their locations are denoted
with a label attached to the ceiling. There is blocking
there for mounting a 5 I/2" diameter speaker. The
stereo location is also denoted with a label attached to
the cabinet where it is to be installed.
Instructional material can be found in the Owner’s
Information Package for the stereo system.
DVD PLAYER/FLAT SCREEN TV
The DVD player is integrated into the stereo. The DVD
player uses the stereo speakers for audio (sound)
transmission when playing a DVD. The DVD player has
both video and audio connections on the back, which is
connected to an audio/video cable that runs to the LCD
TV location. On the factory supplied LCD TV, the video
(yellow) is connected to the “AV-IN2 video” location on
the backside of the TV. The audio right (red) and audio
left (white) are connected to the “AV-OUT AUDIO-R and
AUDIO-L” locations on the backside of the TV.
The LCD TV runs on 12-volt or 120-volt.
To watch a DVD, turn on the TV. Insert the disk into the
DVD player and follow the on-screen directions to play
the movie. Remember that the DVD remote needs to be
pointed towards the DVD player, not the TV to operate.
The DVD player will allow the audio (sound) to play
over the stereo speakers from an over the air or
satellite broadcast. The on screen display (AVI select)
on the the TV needs to be set to “AV” and the DVD
player needs to be set on “AUX”.
LCD TV
If equipped, your camper may have a LCD TV. The
unit runs on 12-volt.
Instructional material can be found in the Owner’s
Information Package.
SATELLITE DISH SELF-POSITIONING
Instructional material can be found in the Owner’s
Information Package.
Positioning the antenna:
1. Turn on antenna power at wall mount plate.
2. Turn on SureLock Signal Meter power button on side
of rotational knob enclosure.
3. Rotate attenuator dial fully clockwise.
• Step 4 Note: LED lights will illuminate from left (next
to power) to right. All LED lights may not illuminate
depending on signal strength.
4. Depress button on rotational knob and rotate an-
tenna until maximum number of LED lights illuminate
on signal meter.
5. Rotate attenuator dial counter clockwise until last
illuminated LED light flickers.
6. Rotate antenna to illuminate last flickering LED Light.
7. Repeat steps 5 and 6 to pinpoint signal reception.
8. Follow instructions for TV or converter box to scan
for available channels.
system in your camper.
EXTERIOR SPEAKERS
Your camper is equipped with exterior with exterior
mounted speakers. The speakers are located on
the curbside of the camper. The wiring for these
speakers terminates at the stereo location. If a CD/
DVD player is installed, the exterior speakers are
connected to the “C” speaker control on the stereo.