26
Before operating the remote control electric camper
jacks, be sure to read and understand the operat-
ing instructions that were provided with your camper
pertaining to their safe operation.
The jacks are operated with a hand held remote
control. To activate the remote, locate the remote
activation switch, which is located at floor level near
the entry door. Press the “WAKE” button on the
activation switch. This will awaken the system and
the red ACTIVE LED will illuminate.
The system will automatically deactivate and enter
sleep mode 10 minutes after the last operation of the
system.
When finished, the LED on the activation switch must
not be lit.
Activate the remote by pressing the POWER+SELECT
button located in the upper left of the remote. The
remote will power up and indicate the green JACKS
LED.
The remote will control either JACKS or ACCESSO-
RIES. If your camper is equipped with a slideout, the
remote will operate the slide. When the green LED is
active, the remote is controlling the JACKS. Pressing
the POWER+SELECT again will change it over to the
yellow LED, which operates the slideout.
When controlling the jacks, the following operations
are possible.
• Extension or retraction of an individual jack.
• Extension or retraction of all 4 jacks.
• Paired operation – adjacent jacks can be oper
-
ated simultaneously by holding down two jack
buttons.
When controlling accessories, only one accessory
can be powered at a time. Multiple accessory button
presses are ignored.
Your remote has been paired to the control unit using
one of the roving codes available, similar to a garage
door opener.
To pair the remote to the control unit:
• Power the system by pressing the WAKE button
on the activation switch. The red ACTIVE LED
should blink 2 flashes with a pause. This indi-
cated that the system is in the default shipment
state, and it has no remote transmitter associ-
ated with it.
• Power the remote by pressing the
POWER+SELECT button. The green LED on
the transmitter will illuminate. The remote will
remain powered for 1 minute.
• Hold down the WAKE button on the activation
switch for 10 seconds. The system will enter
LEARN REMOTE mode which is indicated by
the red ACTIVE LED flashing quickly. In this
mode, the base receiver will associate itself with
the next remote that is received.
• Press any of the jack buttons on the remote.
The base receiver will see the remote and as-
sociate itself with it. At this point, the red LED on
the activation switch should be on solid, and the
blue LED will indicate detection of the remote
signal.
The remote is powered by a 9-volt battery located
under the removable cover on the back of the
remote unit. Always have a spare 9-volt battery
available for your remote. A remote cable is
provided that will allow operation of the remote if
the voltage of battery in the remote becomes too
low to operate the system. Plug the remote cable
into the side of the remote and the other end into
the face of the activation switch.
Summary of Contents for Truck Camper
