3
Correct set position
Correct set position
φ
6
Trigger catcher
OK
(Red colored part)
Incorrect set position
ASSEMBLY
PREPARATION AND INSTALLATION
1
3. Installing casing and built-in guide track
under door bottom
Firmly insert the casing into the pocket as shown,
fasten it with the provided screws.
,QVWDOOWKHJXLGHWUDFNXQGHUWKHGRRU
1. Cutting and drilling holes on upper track
Cut to suitable length. For cutting and drilling holes, refer
to the illustration below.
When cutting, reinforce the track to prevent deformation
at cut section.
2. Preparation of mounting parts
5HFHVVHG UROOHU 3XOO XS OHYHU WR VHSDUDWH
main unit from casing.
:KHQGLPHQVLRQGRRUZLGWK':
is more than 100 mm, provide 4.5 mm
dia. hole at 30 mm from cut face.
5. Assembly of parts and installing upper track
$VVHPEOHWKHSDUWVLQRUGHUIURPWRZLWKFDUHRIGLUHFWLRQ
Tape around recessed roller and upper track to prevent the inserted parts
IURPIDOOLQJ7DNLQJFDUHRIWKHGLUHFWLRQRIWKH/HDGLQJHGJH7UDLOLQJHGJH
install the upper track to the upper frame.
9HUL¿FDWLRQEHIRUHLQVWDOOLQJWKHGXDOVRIWFORVHU
:LWKRXWYHUL¿FDWLRQWKHVHOIFORVLQJIHDWXUHPD\IDLO
,IWKHSRVLWLRQLVZURQJSXOOEDFNWKHWULJJHUFDWFKHUWRWKHFRUUHFWSRVLWLRQXVLQJ
a 6mm diameter round bar.
6. Trigger installation
$FFRUGLQJWRWKH³,QVWDOODWLRQ'UDZLQJ´VHFWLRQLQVWDOOWKHWULJJHUZLWKWKHSURYLGHGVFUHZV
PPIURPWKHOHDGLQJHGJHDQGGRRUZLGWK':PPIURPWKHWUDLOLQJHGJH
Screw in the screws vertically.
,IVFUHZKHDGLVSRVLWLRQHG
outside the trigger, poor function
may result.
3. Remove the jig.
2. Install trigger.
1. Align trigger and mounting
jig with mount hole.
Operation of trigger mounting jig
7. Floor guide
,QVWDOO WKH IORRU JXLGH VR WKDW LW UHPDLQV EHWZHHQ WKH OHDGLQJ DQG
trailing edges of the door when it is opened or closed.
Door width
DW−414
9
Cut side
9
30
9
9
217
2×hole,
φ
5
φ
4.5
(Track mount hole)
2
×
hole,
φ
5
INSTALLATION DIMENSIONS FOR TRIGGER 2
Double sliding
※
Single sliding
Please add the Margin DN to dimension for Trigger 2,
if you are using a protruding handle. Example shown Below.
DW
[Margin DN = 0 mm]
Installation dimension for
Trigger 2
Example [Margin DN = 70 mm]
※
For Double sliding only.
DW+DN-414 is the Installation
dimension for Trigger 2
1,000
586
656
1,100
686
756
1,200
786
856
1,300
886
956
1,400
986
1,056
1,500
1,086
1,156
8
8
DW-414
217
DN+8
DW-414+DN
(see right table)
217
DW-414+DN
(see right table)
DN+8
Margin DN
217
Door width DW = (FW+DK)/2
Margin DN
Door width DW = (FW+DN+DK)/2
Overlap DK
Overlap DK
Margin DN
(in track)
(in track)
Trigger1
Trigger2
Door end
when fully closed
Door end
when fully closed
Trigger2
Trigger1
Trigger2
Trigger1
Casing
Door guide track
(For process dimensions, please
refer to “Installation Drawing”.)
1
2
1
2
217
DW - 414
18
18
Leading edge
Trailing edge
Trigger mount hole
Trigger mounting jig
90°
Trigger
Mounting
screws
90°
Out of straight
Correct installation
Out of straight
Correct installation
OK
OK
Door(Trailing edge)
32
Floor guide
下
上
左
右
(This describes installation of a single sliding door
.)
Main unit
Casing
Lever
Recessed roller
Trailing edg
e
Leading edge
Recessed roller soft closer
two-way soft close
Upper track
Trigger