background image

www.howdens.com

Page _ 10

LAMONA 

Appliances

Hanging your extractor               

  

This instruction must be strictly adhered to. Failure to comply could result in overheating and  

 

serious damage to your appliance. It is recommended that the installation is carried out by two people.

Before drilling or chiselling the ceiling or wall, check for pipes and power cables.

• 

If ducting externally ensure the ducting tube is kept as short as possible and with the minimum 

of bends to permit the smoothest 

 (Maximum length 3 metres.). Ducted air must not be 

discharged into a 

 which is used for exhausting fumes from appliances supplied with energy other 

than electricity. (E.g. gas boilers)

• 

Ensure the requirements of the local authorities are adhered to concerning the discharge of exhaust 

air.

• 

Ensure adequate room ventilation is provided when the extractor is used in the same room as 

appliances supplied with energy other than electricity.

• 

Never duct into a hot air 

 such as a central heating duct

320mm

700 mm Minimum distance to worktop

750 mm Recommended distance to worktop

**  

**

**

**

**

**

Worktop

Wall

73mm

(**) 

Please use rawl plugs and screws appropriate 

to the type of wall (not supplied) 

700 mm Minimum distance to worktop

750 mm Recommended distance to worktop

40 mm 

235mm

195 mm 

Please use rawl plugs and screws 

appropriate to the type of wall 

Wall

 = 

 = 

2

1

2

3

1.

9.

9.

9.

8.

8.

8.

6.

1.  Remove the grease 

 before trying to install.

2.  The recommended 

 height for the hood is 750mm above the worktop. This can be reduced to a 

minimum of 700mm if required.

3.  Mark and drill the holes required to mount the extractor body. 

4.  The principal securing point is bracket ‘6’;   this 

 

5.  With the help of an assistant, hang the extractor body on the bracket level and secure in position 

through the lower two .

Summary of Contents for LAM2505


















Reviews: