background image

Support screws

10mm out of the wall

650 mm Minimum distance 

*750 mm Recommended distance

Worktop

Wall

200mm

60mm

65mm

mm

A

B

B

A

www.howdens.com

Page _ 10

LAMONA 

Appliances

Hanging your extractor               

  

This instruction must be strictly adhered to. Failure to comply could result in overheating and  

 

serious damage to your appliance. It is recommended that the installation is carried out by two people.

Before drilling or chiselling the ceiling or wall, check for pipes and power cables.

Ensure extractor is installed level above the worktop.

• 

If ducting externally ensure the ducting tube is kept as short as possible and with the minimum 

of bends to permit the smoothest 

 (Maximum length 3 metres.). Ducted air must not be 

discharged into a 

 which is used for exhausting fumes from appliances supplied with energy other 

than electricity. (E.g. gas boilers)

• 

Ensure the requirements of the local authorities are adhered to concerning the discharge of exhaust 

air.

• 

Ensure adequate room ventilation is provided when the extractor is used in the same room as 

appliances supplied with energy other than electricity.

• 

Never duct into a hot air 

 such as a central heating duct

1.  Remove the grease 

 before trying to install.

2.  The recommended 

 height for the hood is 750mm above the worktop. This can be reduced to a 

minimum of 650mm if required.

3.  Mark and drill the holes required to mount the extractor body. 

4.  The principal securing point is               is the two upper screws, secure in position but not fully flush.

bracket

 

5.  With the help of an assistant, hang the extractor body on the upper screws and secure in position 

through the lower two mounting screws.

Summary of Contents for LAM2410

















Reviews: