lamber LP8/L-dy, Instruction Manual

Page: 15 / 48

15
For an average water limestone is recommended
cycle activation at least once a week.
The frequency may vary depending on type of
water.
machine «OFF»
Door
closed
Remove the
overflow
keep
button
pressed
for 3 sec.
keep button
pressed for 3 sec
and w
.
ait the End
of the drain
1
2
3
4
To make the cycle do the following operations:
-1
Punt the machine OFF by pressing the
switch “A” (led off)
-2 Remove the OVERFLOW from the tank;
-3 Press the “B” button for 3 seconds and
wait for the complete emptying of the
tank;
-4 Close the door of the machine;
-5 Then press the “E” button for 3
seconds
At the end of the descaling cycle (approx. 35
minutes) will appear on the LED the words
“END OF THE DESCALING CYCLE”.
List of automatic MESSAGES
On the display may appear some messages to
inform about the status of the cycle start of
abnormalities. Below is the eXplanation of some
MESSAGES that appear on the display
automatically.
1-BREAK TANK :
This indicates that the tank of Break Tank is
filling of water to reach the required level.
2-ALLARME BREAK TANK:
This indicates a fault in the operating system:
lack of water mains, valve not functionning: Call
Customer Service!
3-ECONOMY :
After 10 minutes of non-use of the machine with
hood open, it appears the word ECONOMY.
The temperature of the heater stabililzes at 60°
reducing the consumption of energy.
4-OFF
If no button is pressed in 1 hour, the message
“OFF” will appear and the machine turns off.
5-THERMOCONTROL :
This indicates that the washing cycle will be
extended to reach the ideal temperature for
rinsing
This message is accompanied by the value of the
temperature. This gives flashes and increments
until it reaches the programmed temperature, at
which may start the rinsing phase.
6-REMOVE OVERFLOW :
This indicates that the overflow has to be
removed to perform the selected operations (self-
washing, descaling or discharge of the tank)
The data is highlighted even if in reality you have
already removed the overflow, but will disappear
automatically after 10 seconds after you close
the hood of the dishwasher.
7-REGENERATION IN PROGRESS :
(only for machines with built-in water softener).
It indicates that a cycle of regeneration of the
resins varying from 30” to 90” seconds is in
progress.
8- WASH OF THE RESINS :
(only for machines with built-in water softner).
It indicates that a washing cycle of the resins of
the duration of 10” seconds is in progress..
9-SALT :
(only for machines with built-in water softener)
It indicates that there is a lack of salt into the
container. Add big pads of salt into the container
as per the specifications given to you by your
provider.
10-SERVICE :
It Iindicates that you need to do maintenance
work. The scheduled maintenance service allows
you to control all the devices and efficiently
maintain your dishwasher over the time. Normal
functioning is still guaranteed. It is well worth
however not to wait too long to make the
intervention
.
List ALARMS!
Alarm: A3-TEMP.SENSOR : this message
indicates that the probe of the tank temperature
thermostats or boiler is defective. Call the
Technical Support Service!!
Alarm: A2-HIGH TEMP. : this message indicates
that the temperature in the boiler is greater than
105°C. Call the Technical Support Service!
Alarm: BOILER PROBE FAILURE. : this
message indicates that the probe of the boiler is
not working properly. In this case the functioning
of the resistance of the boiler and the
Thermocontrol are disabled.
Call the Technical Support Service!
Alarm: TANK PROBE FAILURE: this message
indicates that the probe of the washing tank is
not working properly. It is disabled in this case
the functioning of the washing tank resistance.
Call the Technical Support Service!