Just TWIS
T
to CLEAN
Safety Latch
Stabilizer Bolts
(not provided by LAKOS)
Gasket/Housing
O-Ring Kit
131729 (T2C-075 and 100)
Filter Element Kit (incl. Pin)
131730 (30 Mesh)
131731 (60 Mesh)
131732 (100 Mesh)
131733 (140 Mesh)
Pin & O-Ring Kit
132093 (T2C-075-100)
Bowl & O-Ring Kit
131728 (T2C-075-100)
T2C-
075-100
www.TWISTIICLEAN.com
TWIST
II
CLEAN removes sand and organics as the water
passes through the filter element. Periodic cleaning is
necessary to optimize filter performance, reduce the
pressure loss
and prolong
the product life.
When the filter
element looks
like it is filled with
debris, it should be
cleaned.
Just a gentle
1/4 clockwise
TWIST of the
top handle begins
the patented reverse flushing action. In just a few seconds, all
debris are backwashed off the filter element and flushed out
the bottom of the Purge Exit port. BE SURE TO RAISE THE
SAFETY LATCH BEFORE TWISTING THE HANDLE AND
LOWER IT AFTER FLUSHING.
Using Your TWIST
II
CLEAN
Normal Mode
Flush Cleaning
Mode
Water Flow Direction
TWIST
II
CLEAN
Exploded View
and Spare Parts
Maintenance and Troubleshooting
If for any reason the filter element does not clean
completely during the normal Twist to Clean operation,
manual cleaning may be needed. In this case, remove
the bowl and clean the element with a soft nylon brush,
brushing and running water across element.
Caution:
If the filter bowl is to be removed, all water
flow must be shut off going to the filter.
Safety Notes:
Despite the ease of installation and operation of the LAKOS
TWIST
II
CLEAN product, certain precautions should be taken.
1. Lubricate “O” rings with NSF approved silicon grease only -
Dow 111 is recommended.
2. Do not overtighten the threaded connections. Do not
tighten more than a 1/4 turn past finger tight. Hand tighten
the bowl, do not use tools.
3. Do not use wrenches on plastic filter parts. Use of tools on
filter will void warranty.
4. For threaded connections, use the
PTFE
sealant tape
provided
with product.
5. Filter components that have “O” rings do not require thread
sealant.
6. Remove clear bowl if the filter is to be installed using any
solvent welding. This will prevent solvent damage to the
clear bowl.
7. This filter is designed for use with water only. Other
chemicals or components can damage the filter
components. Evaluate all chemicals for proper usage with
the filter.
8. Protect unit from freezing, as you would with any other
water supply lines.
9. Follow all local and state codes, laws, and regulations
when installing any filter.
10. If removal of the screen element is necessary, take care
not to damage the element or the components that hold
the element in place. The T2C-150 model has latching
clips that hold the element in place. Do not spread the clips
more than necessary to remove the element.
Limited Warranty
The LAKOS TWIST
II
CLEAN is warranted to be free of material or workmanship defects for at
least one year from delivery date.
If a fault develops, notify us, giving a complete description of the alleged malfunction. Include
the model number(s), date of delivery and operating conditions of subject product(s). We will
subsequently review this information and, at our option, supply you with either servicing data
or shipping instruction and returned materials authorization. Upon prepaid receipt of subject
product(s) at the instructed destination, we will then either repair or replace such product(s), at
our option, and if determined to be a warranted defect, we will perform any products, damages
or injuries resulting from misuse, neglect, normal expected wear, chemically-caused corrosion,
improper installation or operation contrary to factory recommendation. Nor does it cover equip-
ment that has been modifed, tampered with or altered without authorization. No other extended
liabilities are stated or implied and this warranty in no event covers incidental or consequential
damages, injuries or costs resulting from any such defective product(s).
Safety Latch
O-Ring Kit
132346
Bowl & O-Ring Kit
132236 (T2C-150)
Filter Element Kit (incl. Pin)
132232 (30 Mesh)
132233 (60 Mesh)
132234 (100 Mesh)
132235 (140 Mesh)
Gasket/Housing
O-Ring Kit
132237 (T2C-150)
Stabilizer Bolts
(not provided by LAKOS)
T2C-075
T2C-100
T2C-150
For proper
purging of your
TWIST
II
CLEAN,
lift the red safety
latch prior to
twisting the
handle.