Laguna Tools Fusion 3, Manual

Page: 13 / 40

Fusion Tablesaw
© 10/2017, Laguna Tools, Inc.
11
Setup
Use Caution:
Your new Laguna Tools machine is heavy. Use a
minimum of two people when lifting the tool into position and moving
the tool into position.
warning:
To avoid set-up problems, to prevent potential damage to
the machine and personal injury, read through the entire setup
section prior to setting up the machine.
Tech Tip:
A setup video is available at
lagunatools.com/classic-machinery/tablesaws/f2-fusion/
or www.youtube.com/watch?v=FOPstZ61uFs
warning:
DO NOT connect to a power supply until the setup is
complete. DO NOT perform any of the following steps, installations,
or adjustments with the saw connected to the power source.
Receiving and Unpacking
If any damage has occurred because of shipment, note the damage on the bill of lading or refuse the shipment. Immediately call the dealer store
where the machine was purchased.
1. Receiving your tablesaw.
2. Unscrew the crate fasteners.
3. Lift crate off pallet.
4. Check Inventory.
5. Wipe off protective oils.
This is how the machine is shipped from the
factory.
Use a drill or screw driver with a #2 Phillips head
bit and remove the bottom screws from carton.
These screws may be discarded.
Use two persons to lift the carton away from the
pallet. There should be three packages along with
the tablesaw.
NOTE: The throat plate, riving knife, and 10” blade is pre-installed in
the machine. The miter gauge, and blade changing tool are positioned
in the tool holder located on the right side of the cabinet.
1. Fence, install tools, push stick, blade
guard assembly
2. Smaller fence rail sections, hardware kit
3. Longer fence rail sections.
Peel back the protective vinyl plastic and wipe
away the oil with a waste rag.
Use Caution:
An oily rag can be a
serious fire hazard. Discard in an
appropriate manner.
Tech Tip:
To help keep your table top clean and to prevent or clean any rust, we recommend waxing your tabletop with an appropriate wax rubbing
compound. This will also reduce friction under operation. Rust can be removed with WD-40.
Inventory
Box 1 contents Box 2 contents Box 3 contents Pre-Installed on machine
Fence
PTSF236110175-0130-1-1
Rear Rail 2
PTSF236110175-0130-127.5
Rear Rail 1
PTSF236110175-0130-127.5
Throat Plate
PTSF236110175-0130-6
Push Stick
PTSF236110175-0130-130
Front Rail 2
PTSF236110175-0130-127.6
Front Rail 1
PTSF236110175-0130-127.6
Riving Knife
PTSF236110175-0130-27
Blade Guard
PTSF236110175-0130-2-1
Hardware kit
-
10” Blade
PTSF236110175-0130-33
Install Tools
-
Miter Gauge
PTSF236110175-0130-3
Fence Hooks*
PTSF236110175-0130-118
Arbor Wrench
PTSF236110175-0130-137
*Fence storage hooks may be pre-installed. Tool Storage PTSF236110175-0130-120
Wing (2) PTSF236110175-0130-4
Notice:
The front rail part number is comprised of two pieces – both long and short. The rear rail part number is comprised of two pieces – long and
short.
NOTICE:
For safety reasons, this machine is not sold with a tape-rule for the left side of the blade. It is not a missing part.
Receiving your tablesaw
Lift crate off pallet Check Inventory Wipe off protective plastics
Unscrew the crate fasteners