manualshive.com logo in svg

laerdal Reusable, User Manual

Share
Download
laerdal Reusable User Manual Download Page 26

26

Battery

Charge the Battery

The internal rechargeable battery can be charged directly from external AC or DC power. 
1.  Ensure the Operating Knob is set to “0”. 

2.  Connect either external AC or DC power to the LSU and charging will start 

automatically.

3.  During charging, the Battery Status Indicator will indicate approximate achieved 

battery capacity. Minimum charging time for full charge is 4 hours.

A completely discharged battery cannot be charged by the LSU and must be replaced. 

If LSU battery is kept on constant charge, perform device test at least once a month to 

exercise battery.

 Cautions

•  Do not perform the Device Test during battery charging.

•  The recommended ambient temperature for charging is from 15°C to 25°C.

•  The battery will not be charged when the LSU is in operation.

Check the Battery Quality

If poor battery quality is suspected, charge the battery for a minimum of 4 hours and 

then perform the following test.  Do not connect to external power. 

 

    

1.  Run the Device Test.  

2.  Let the LSU operate continuously at 500+ mmHg setting and free air flow for  

20 minutes.

3.  If the LSU stops before completing the 20 minutes, the battery should be discarded.

 Caution 

Replace the battery when it does not pass the Battery Quality Check or after 3 years, 

whichever comes first.

Summary of Contents for Reusable









































Reviews:

No comments

Brands by name

Popular brands

Load more brands