background image

6

Thermostat cartridge

The thermostat cartridge is available as a spare part, and 
may need to be replaced more often if it is regularly exposed 
to temperatures close to, or above, boiling point.

The number is engraved on the cartridge.

No. Opening 

temperature

5839 63°C

8719  

72°C   

1456  

78°C

1467 83°C

Service

Before carrying out any servicing work, close the three shut-
offs by turning the lever on the valves at right angles to the 
direction of the pipe. This makes it easy to access the pump, 
thermal valve and check valve for service.

If operating interruptions still occur, even though the 
system has been bled, there may be dirt such as lint, tape or 
thread swarf stuck in the coupling. Disassemble and clean. 
Clean all sealing surfaces when reassembling:

1. The thermal valve 

2. The self-circulation valve

3. The pump impeller

In some installations, there are problems with extremely 
high levels of contaminants. These can form deposits inside 
the pump, which may result in stoppages. 

Instructions for replacing the 
thermostat in Laddomat 21-60

Check that the pump is switched off. 

Close the three shut-offs. 

Unscrew the cover opposite the pump.

Remove the cover with the spring, plunger and thermostat 
from Laddomat 21-60. 

The thermostat is held in place on the plunger by an O-
ring. Detach the thermostat from the plunger carefully 
using a screwdriver (see image on right). 

Push the new thermostat into the plunger. 

Reinstall the cover with the spring, plunger and thermostat. 
Open the shut-off valves.

Wait a few minutes before starting the pump to allow any 
air to rise and escape from the system. 

The installation is now ready for use.

Blocking the check valve

If you, for some reason, want to completely shut off the self 
circulation function, the check valve must be blocked.
Use the blocking clip, placed at the bottom of the EPP-
insulation (Picture 3), to block the check valve. 
The clip is then fastened around the check valve axis ac-
cording to picture 5.
To reach the axis, the spring needs to be removed.

Picture 2

Picture 1

Picture 4

Picture 5

Picture 3

The blocking clip is 
mounted here.

Blocking 
clip

Summary of Contents for 21-60







Reviews: