manualshive.com logo in svg

Lacerta M-GEN, User Manual

Share
Download
Lacerta M-GEN User Manual Download Page 31

- 31 - 

  

Note: it may occur that the correction (guider imaging) frequency is so frequent that 
both of the correction signals could not be put out fully. In this case the new correction 
signal gets active and the current is interrupted. It may delay the DEC corrections if 
the RA must be corrected continuously. 
 

 

dead time

: (

decimal, 0..248 ms (31 ms step)

) profile 

If Exclusive AG out mode is used, this value defines the wait time (no AG signal) 
between the signal changes. The default value (used in preceding firmwares) is 62 ms. 
Use LEFT and RIGHT buttons to change the value. 
 
This is a workaround for some mounts that can’t recognize/handle perfectly sudden 
AG signal direction changes. 
 

 

AE mask warning

: (

switch

) profile 

This enables a warning before starting and AutoExposure program. The warning is 
shown if the focuser mask is on or off the telescope. Only after one second can the 
user affirm the start with SET button or cancel it with ESC. 
 

 

Emulation mode

: (

switch

) global 

If this mode is checked, the Camera’s star data is ignored and the HC uses an emulated 
mount and guiding setup, an “emulated star”. This is shown as a single dot in the 
guiding window. A cross mark shows the current guiding center position. The guiding 
window does not folow this “star”, it is held constant. This mode is very useful at 
testing and getting acquainted with the functions in room. 
Some latency by the mount, seeing and the effect of the integration time is also 
emulated. There are no backlash in this system. 
 
The emulated setup is the following: 
 

- RA is horizontally 

- DEC is vertically 

- Focal length is 180mm 

- AG speed is 0.5x 

- RA is 0.8x DEC speed 

 

 

 

Factory reset

: (

button

) 

Using this button You can reset ALL the saved parameters/variables in the device 
back to factory (firmware) default. All active function will be stopped like 
autoguiding, Camera will be turned off and file will be closed. After resetting the 
variables, the firmware continues from this screen. 
 

WARNING

: please note that ALL variables are reset, regardless of what You know 

about. You have to check and set them all again for all the profiles. Here’s a checklist 
that could help You to do so: 
 

−

 

 all 4 AutoExposure programs and prg. list 

−

 

 latest calibration (need to do a new one), axis inversion 

−

 

 RA/DEC guiding parameters and backlash 

−

 

 image processing mode (resets to OLD and full window processing!) 

−

 

 guider scope focal length, mount’s AG speed and CCD binning 

−

 

 RD (dithering) settings 

Summary of Contents for M-GEN
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands