background image

 

User Manual LabModul 240

 

Page 7

 

www.labtec.de

 

Test 

step

 

Operation

 

Comments

 

Controls

 

1.1.1

 

Wet the outlet valve rubber slice. Breathing con-

nection  of mask close with the dust cap.

 

Flutter valve must be thoroughly moist

 

 

1.1.2

 

Mount mask on test head, pull straps tight, 

inflate test head (3)

 

A few seconds is usually long 

enough 

 

    

 

1.1.3

 

Adjust negative pressure to exactly 

-

 #

 

mbar 

(6)

 

By means of pressure relief valve 

(7)

 

 

1.1.4

 

Pressure increase after # min at the  LCD (LP) 

read off and compare with  the nominal value

 

 

 

1.1.5

 

Deflate test head (4), remove mask

 

 

 

 

 

 

 

1.2.1

 

Wet the outlet valve rubber slice. Breathing con-

nection  of mask close with the dust cap.

 

Test only possible with tight

-

set A

-

valve. Use mark specific adaptors.

 

 

1.2.2

 

Mount mask on test head, pull straps tight, 

inflate test head (3)

 

A few seconds is usually long 

enough 

 

 

1.2.3

 

Adjust negative pressure to exactly 

-

 #

 

mbar 

(5)

 

By means of pressure relief valve 

(7)

 

 

1.2.4

 

Pressure increase after # min at the  LCD (LP) 

read off and compare with  the nominal value

 

 

 

1.2.5

 

Deflate test head (4), remove mask

 

 

 

 

 

 

 

1.3.1

 

Mount mask on test head, pull straps tight, 

inflate test head

 

A few seconds is usually long 

enough 

 

 

1.3.2

 

Pump  +10  l/min switch on.

 

 

 

1.3.3

 

Opening pressure at the LCD (LP) read off and 

compare with  the nominal value

 

 

 

1.3.4

 

Pump  +10  l/min switch off (8).

 

 

 

1.3.5

 

Deflate test head (4), remove mask

 

 

 

1

 

Leakage

 

1.1

 

Leakage test with open A

-

valve at 

--

#

 

mbar (standard test, should always be carried out)

 

1.2

 

Leakage test with sealed A

-

valve at +#

 

mbar (performed to locate any leak detected by test 1.1)

 

1.3

 

Opening pressure of the outlet valve

 

A 1

 

testing full

-

face masks

 

Summary of Contents for LabModul 240 Series












Reviews: