background image

 

 

  Page | 10                                                                                Revision 1.4                                                                 15 January 
2015

 

Record operation in detail 

 

LabSat 3 uses SD card and HDD memory for storage and playback of GNSS data.  It is important to note that 
Class 10 or higher cards must be used to sustain the transfer speeds required.  When recording two 
constellation types, the data rate is approximately 8.2MB (Mega Bytes) per second.  To ensure that data is 
collected without error, the card should be able to sustain 10MB per second. Spare cards and HDDs may be 
purchased from Racelogic.  

 

It is important that cards are formatted as FAT32. LabSat 3 is able to format cards and HDDs in FAT32 with 
the optimum configuration for high speed recording.  When a card or HDD is formatted by LabSat 3, it will 
also carry out a performance test to determine whether or not the media can sustain the required 
bandwidth and inform the user if this is not the case. 

 

For record capable systems, the LabSat will be supplied with a magnetic mounting GNSS antenna. The 
antenna is an active device with approximately 28dB of gain.  The LabSat provides a 2.85V DC bias for 
antenna power on the centre pin of the RF IN connector. It is also possible to use third party antennas 
providing they are compatible with the 2.85V bias.  If connecting LabSat to an antenna which requires a 
higher bias voltage (e.g. 12v), the antenna bias must be supplied by the user and an appropriate DC block 
(such as DCB from 

http://gpsnetworking.com/attenuators.asp

) must be inserted at the LabSat 3 RF IN 

connector to avoid damage to the LabSat. 

 

There are a number of GNSS systems currently in operation or in a test phase. These operate on 3 main 
frequency bands. These are:- 

 

 

 

 
 
 
 

 

Depending on the model, LabSat 3 will have 1, 2 or 3 RF channels. This allows recording of 1, 2 or 3 
frequency bands so, for example, a 2 constellation LabSat 3 may record the band containing GPS L1/Galileo 
E1 and the band containing GLONASS L1 simultaneously.  Recording of the desired constellations is 
configured in the CONSTELLATION menu.  In this menu, the user can tick up to three of the desired 
constellation groups (depending on version).  If only one constellation is ticked, then an additional option 
for 2bit will be available to allow 2bit quantized recording for the selected constellation. 

 

Once the constellations are configured, exit the menu and press the REC button to begin recording. A new 
file will be created each time recording starts.  The file name used corresponds to the constellations 
selected.  For example, if GPS and GLONASS are selected for recording, the file created will be GPSGLO_nnn 
where nnn is a number that increments with each new recording.  Details of the LS3 file format are 
available on request from Racelogic. 

 

During recording, pressing the OK button will switch the display to show satellite levels for either GPS or 
GLONASS satellites.  In this display mode, the up and down arrow keys will toggle between GPS or GLONASS 
constellations.  BeiDou constellation is not currently supported by the internal monitor but BeiDou B1 
signals can still be recorded and replayed. 

 

To maximize battery life during recording, LabSat 3 has a power save mode which is enabled by default I n 
the setup menu.  Power save mode recognizes when running from battery power and will dim the display 
backlight and power-down the internal GPS/GLONASS monitor after 30 seconds of user inactivity.   

 

If recording from passive antennas such as the Maxtenna M1516HCT-SMA GPS/GLONASS antenna, enabling 
the power-save mode will also provide the highest possible sensitivity by ensuring that unused modules 
within LabSat 3 are switched off. 

Frequency Band 

Constellations 

1575.42MHz 

GPS L1, Galileo E1, QZSS, SBAS 

1602MHz 

GLONASS L1 

1561.098 

BeiDou B1 

Summary of Contents for 3 Wideband




























Reviews: