Labnet I-4001-HCS Instruction Manual Download Page 5

  Instruction Manual        | 

         3

 5.0  Specifications

Working environment temperature

10°C to 30°C

Storage environment temperature

-20°C to 50°C

Environmental conditions

≤70% RH, 70 to 106 kPa

Electrical

I-4001-HCS 
I-4002-HCS

AC 120V ±10%, 50/60Hz, 150W 
AC 230V ±10%, 50/60Hz, 150W

Fuse

I-4001-HCS 
I-4002-HCS

125V, 2.5A, 5 x 20 mm 
250V, 1.5A, 5 x 20 mm

Dimensions (L × W × H) 

12.9 x 6.5 x 9.8 in. (328 × 166 × 249 mm)

Weight 

18.75 lbs. (8.5 kg)

Temperature control range

0°C to 105°C

Temperature range

Room temperature -14°C to 100°C

Timing range

1 min. to 99 hrs. 59 min.

Cooling time

From room temperature to room temperature -10°C:  ≤8 min.

 

From 100°C to room tempe10°C: ≤15 min.

Heating time

≤12 min. (from 20°C to 100°C)

Temperature accuracy

≤±0.5°C

Temperature uncertainty

≤±0.5°C

Heating rate

About 6°C/min. (from 20°C to 100°C)

Block temperature uniformity

≤±0.5°C

Mixing rate

300 to 1,500 rpm

Amplitude

3 mm

The Labnet Microtube Shaking Incubator is designed to be safe at least when operated under the following conditions:

 



Indoor use

 



Pollution Degree 2

Summary of Contents for I-4001-HCS














Reviews: