La Marche A36D Instructions Manual Download Page 8

MODEL A36D SERIES - INSTRUCTIONS AND TROUBLESHOOTING

 

Page 8 of 33 

4.5 

STATUS/ALARM INDICATORS  

Alarm Relays 

Dual  Form  “C”  contacts  are  rated  for  28  VDC  at  2  amperes  for  the  low  current,  low  DC  voltage,  high  DC 
voltage, high voltage shutdown, blown DC protection, summary and load shore.  All alarms have adjustable 
time delay on energize. 

AC “ON” Indicator 

A green light emitting diode (LED) indicator illuminates to indicate AC voltage is present to the rectifier. 

High-Voltage Alarm Indicator 

A  red  LED  indicator  blinks  to  indicate  that  rectifier  output  has  exceeded  the  preset  high-voltage  set  point.  
This alarm condition will also trigger the summary “failure” alarm contacts. 

Low-Voltage Alarm Indicator 

A red LED indicator blinks to indicate that the rectifier output has dropped below a preset voltage set point.  
This alarm will also trigger the summary “failure” alarm contacts. 

Low-current Alarm Indicator 

A red LED indicator illuminates to indicate that the rectifier output current has fallen below .5% of rectifier 
rated  DC  output.    This  alarm  may  also  trigger  the  summary  “failure”  alarm  contacts  provided  “YES”  is 
selected in the calibration routine if low current is a failure condition. 

Summary Fail Alarm Indicator 

A red LED illuminates to indicate that a failure has occurred which may disable the rectifier.  The conditions 
which  will  produce  a  summary  failure  indication  include:  low  current*,  low  output  voltage  or  high  output 
voltage.  2 form “C” contacts are provided for connection of external alarms. 

* - Provided low current is selected for summary alarm condition. 

Float Indicator 

A green LED illuminates to indicate that the rectifier is in the float mode of operation. 

Equalize Indicator 

A yellow LED illuminates to indicate that the rectifier is in the equalize mode of operation. 

DC Blown Fuse Indicator 

A red LED illuminates to indicate that the main DC protection device has opened. 

Adjustments are provided for high voltage, low voltage, low current, and high voltage shutdown. 

See Section 9 “ALARM LIGHTS”. 

4.6 

PARALLELING 

This rectifier will parallel with any other La Marche Model A36D Charger. 

Summary of Contents for A36D


































Reviews: