background image

 

 

 

Folding and Storage 

 

 

1.  Unclip the tow bar safety strap from the D ring and remove the pin and hitch 

from the bike frame. 

2.  Clip the end of the strap back onto the tow bar D ring. 

3.  Remove the flag and pole and separate into 3 sections. 

4.  Remove the screw cap from the rear axles of the rear wheels. 

5.  Remove the quick release pin from the tow bar bracket at the front corner 

of the Bike Trailer. 

6.  Fold the tow bar back under the Bike Trailer and replace the quick release 

pin through the tow bar and U channel. 

7.  Place wheels and flag pole inside the passenger compartment and close the 

front cover. 

8.  Remove the Four Season Cover. 

9.  Loosen the crossbar knob and remove. 

10. Fold the crossbar down to allow the window tubes to fold in . 

11. Fold the cabin as shown below. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Fig 22) 

(Fig 23) 

 

 

 

          Before Every Use 

 

 

1.  Make sure all parts are in goood working order and none are missing. 

2.  Do not use the Bike Trailer if any parts are worn or missing. 

3.  Check all fastners are securely tightened. 

4.  Check all tyres to ensure they are properly inflated. 

5.  If you have any questions about proper use please contact the 

qualified technician. 

 
 

Summary of Contents for ZKI-BT













Reviews: