background image

 

8

displayed. If they are not shown in LCD after 60 seconds, remove the batteries 
and wait for at least 60 seconds before reinserting them.  

4.  The outdoor temperature and humidity from the first sensor (channel 1) should 

then be displayed on the Weather station. If this does not happen and the signal 
reception icon is not shown, after 2 minutes, the batteries will need to be 
removed from both units and reset from step 1. 

5.  Insert the batteries to the second sensor as soon as the outdoor temperature and 

humidity readings from the first sensor are displayed on the Weather station.   

NOTE:  You must insert the batteries into the second sensor within 30 
seconds of reception of the first sensor. 

6.  The outdoor temperature and humidity from the second sensor and the "channel 

2" icon should then be displayed on the Weather station. If this does not happen 
after 2 minute, the batteries will need to be removed from all the units and reset 
from step 1. 

7.  Insert the batteries to the third sensor as soon as the "channel 2" icon and 

outdoor data are displayed on the Weather station. Then within 2 minutes, the 
channel 3 outdoor data from the third sensor will be displayed and the channel 
icon will shift back to "1" once the third sensor is successfully received. If this is 
not happen, user shall restart the setting up from step 1.  

NOTE:  You must insert the batteries into the third sensor within 30 seconds of 
reception of the second sensor. 

 

IMPORTANT: Transmission problems will arise if the setting for multiple 

sensors is not followed as described above. Should transmission problems 
occur, it is necessary to remove the batteries from all units and start again the 
set-up from step 1. 

 

D. VIEWING AND OPERATING WITH MULTIPLE REMOTE SENSOR UNITS

 

1. To view the temperature of a different thermo-hygro sensor unit, press and release 

the 

SET/CH

 button.  A shift from one “boxed” number to the next should be 

observed on the right side of the OUTDOOR LCD.  

2. To view the Minimum/Maximum temperature & humidity : first select from which 

thermo-hygro sensor to read data (indicated by the “boxed” number).  Pressing and 
releasing the 

MIN/MAX

 button will toggle through the minimum and maximum 

indoor temperature, and the minimum and maximum outdoor temperature and 
humidity. 

3. To reset the Minimum/Maximum readings, press and hold the 

MIN/MAX 

button for 

5 seconds. 

 

III. MOUNTING 

Note:

  To achieve a true temperature reading, avoid mounting in direct sunlight. We 

recommend that you mount the thermo-hygro sensor on an outside North-facing wall 
(under the eve of a house is ideal).  The sending range is 330 feet; obstacles such as 
walls, stucco walls, concrete, and large metal objects will reduce the range.  Place the 
Wireless Weather Station and thermo-hygro sensor in their desired locations before 

Summary of Contents for WS-8300U













Reviews: