La Crosse Technology WS-8001U Instruction Manual Download Page 10

MOUNTING 

 

There are two possible ways to mount the Moon Phase Clock: 
 

• 

use of the foldout table stands, or 

 

  

  

 

 

  

 

 

  

  

  

  

  

  

 

 

  

  

 

Function Buttons 

Foldout Table Stands 

Hanging Holes 

 

10

• 

wall mounting. 

 

I)  FOLDOUT TABLE STANDS 

 

The Foldout table stand legs are located on the backside, 
at the lower corners, and on both sides of the battery 
cover.  The hinges are towards the edges of the Moon 
Phase Clock, and the ends (with no hinge) need to be 
folded out towards the edge.  Once the Foldout table 
stands are extended, place the Moon Phase Clock in an 
appropriate location. 

 

II) WALL MOUNTING 

 

1)  Using a straightedge, horizontally space at 3-

15/16 of an inch (100.58mm) three screw 
positions on a wall.   

2)  Install three mounting screws (not included) into 

a wall within transmission range—leaving 
approximately 3/16 of an inch (5mm) extended 
from the wall.

 

3) 

Place the Moon Phase Clock onto the screws, using the hanging holes on 
the backside.  Gently pull the Moon Phase Clock down to lock the screws 
into place.

     

 

 
 

Summary of Contents for WS-8001U














Reviews: