background image

 

22

SPECIFICATIONS 
 
Temperature measuring range: 

Indoor: 

32

°

F to 139.8

°

F with 0.2

°

resolution.  (0

°

C to 59.9

°

C with 

0.1

°

C resolution).  “OFL” 

displayed if outside this range. 

Outdoor: 

-21.8

°

F to 157.2

°

F with 0.2

°

resolution.  (-29.9

°

C to 69.9

°

resolution).  “OFL” displayed if 
outside this range. 

 

Indoor relative humidity 
measuring range: 

19% to 95% with 1% 
resolution.  (“- -” displayed if 
outside this range. 

Indoor Temperature checking 
interval: 

Every 10 seconds. 

Indoor Humidity checking 
interval: 

Every 1 minute. 

Outdoor Temperature checking 
interval (Remote Control 
Sender): 

Every 1 minute. 

Outdoor Temperature reception 
(Weather Station): 

Every 5 minutes. 

Transmission Range: 

80 feet (in open space). 

Power Supply: 

Weather Station: 

2 x AA, IEC LR6, 1.5V. 

Temperature Sensor: 

2 x AA, IEC LR3, 1.5V. 

Battery life cycle: 

Approximately 12 months. 

Recommended battery type: 

Alkaline. 

 

 

Dimensions (L x W x H) 

Weather Station (without 
stand): 

3.54 x 1.18 x 5.43 in   
(90 x 30 x 138mm). 

Temperature Sensor: 

1.57“ x 0.9“ x 5.04“  
 (40 x 23 x 128 mm) 

 
 

Summary of Contents for WS-7014U

























Reviews: