background image

System Requirements for PC use: 

 

1. Introduction 

The minimum system requirement for use of this “Heavy Weather” 
software is:  

 

 

Thank you for purchasing this Professional Remote Weather Station. 

  

 

Operating system: Windows 98 or above

 

Designed for everyday use, the weather station will prove to be an 
asset of great value for your personal use in the home or office. 

Processor: Pentium 166 MHz or above

 

RAM: 32MB of RAM or above

 

  

Please read this instruction manual thoroughly to fully understand the 
correct operation of your weather station and benefit from its unique 
features. 

Hard disk: 20MB free space 
CD-ROM drive 

 

 

For full details on operation and installation of the “Heavy Weather” 
software refer to the PC manual in PDF format on the CD-ROM. 

2. 

Intended Use  

 

 

Weather Station 

Features of the base station: 

The base station measures the indoor environment of its surrounding 
area and receives weather data from the following three outdoor 
sensors: 

• 

Receives and displays the WWVB radio controlled time and date  

• 

Display of extensive weather data, in all cases with programmable 
alarm functions for certain weather conditions as well as records of 
all minimum and maximum values along with time and date of their 
recordings 

1) Thermo-Hygro 

Sensor 

2) Wind 

Sensor 

3) Rain 

Sensor 

• 

Indoor and outdoor temperature displays in degrees Fahrenheit or 
Celsius (user selectable) 

 

The received data is continuously updated to bring you the latest 
weather information on the base station’s LCD.  The outdoor thermo-
hygro sensor is the main data communication unit since both the wind 
and rain sensors are connected to the thermo-hygro sensor for 
operating power and rely on it to communicate to the base station.  
Weather data sent from the thermo-hygro sensor can be done by 
wireless 433MHz transmission (up to 100ft in open space) or by cable 
connection. 

• 

Indoor and outdoor relative humidity displays 

• 

Air pressure reading in inHg or hPa, absolute or relative (user 
selectable) 

• 

Detailed display of rainfall data in 1 hour, 24 hours, total since last 
reset (user selectable in mm or inch) 

• 

Wind speed in mph, km/h, m/s, knots or Beaufort (user selectable) 

• 

Wind direction display with LCD compass as well as numerical (e.g. 
225°) and abbreviated characters (e.g. SW) 

 

Using the enclosed 6.5ft computer cable and CD-ROM, you can 
install the Heavy Weather software to your PC and access the latest 
weather information from your PC and upload up to 175 sets of 
recorded weather data received by the base station.  Recorded data 
can be used to generate statistics and charts onto your spreadsheets 
(175 sets of data is stored in the base even if the PC is switched 
OFF).  The software itself does not set any limits as to how many data 
sets can be transferred to PC. 

• 

Wind chill temperature display 

• 

Dew point temperature display 

• 

Weather forecast display by weather icons (sunny, cloudy, rainy) 

• 

Weather tendency indicator 

• 

Storm warning alarm 

• 

LED back light 

• 

Simultaneous display of all weather data with individual settings by 
the user 

 

• 

COM port for easy connection to your PC 

This weather station is designed to work easily with your PC, simply 
connect and disconnect the PC cable at any time. 

• 

All the weather data from the base station and up to 175 sets of 
weather history data with user adjustable measuring intervals can be 
recorded and uploaded to your PC 

 
 

 

 

 

Summary of Contents for WS-2310





















Reviews: