background image

 

37 

 
RADIO CONTROLLED TIME 

The time base for the radio controlled time is a Cesium Atomic Clock operated by the 
Physikalisch Technische Bundesanstalt Braunschweig which has a time deviation of 
less than one second in one million years. The time is coded and transmitted from 
Mainflingen near Frankfurt via frequency signal DCF-77 (77.5 kHz) and has a 
transmitting range of approximately 1,500 km. Your radio-controlled Projection clock 
receives this signal and converts it to show the precise time in summer or wintertime. 
The quality of the reception depends greatly on the geographic location. In normal 
cases, there should be no reception problems within a 1500km radius of Frankfurt.  
 
The DCF tower icon in the clock display will start flashing in the upper center. This 
indicates that the clock has detected that there is a radio signal present and is trying to 
receive it. When the time code is received, the DCF tower becomes permanently lit and 
the time will be displayed. 
If the tower icon flashes, but does not set the time or the DCF tower does not appear at 
all, then please take note of the following: 

Summary of Contents for RADIO CONTROLLED PROJECTION ALARM CLOCK


























Reviews: