background image

 

TARGA SYSTEMS

 

 

S4 SATA & USB DTU  Installation Guide 

32003444   Rev A

 

 

 

 

 12

 

4

 

Warranty & Repair 

 

Targa products are designed, manufactured and tested to the highest industrial standards, 
however repair may become necessary sometime during the life of the unit. If you believe 
your Targa product requires repair, please follow these guidelines to ensure prompt, 
accurate service: 

 

      1. Carefully note the symptoms of the problem you are experiencing, along with the 

model and serial number of the product. 

 

      2. Call Targa Customer Service Support at (613) 727-9876.  

A technician will discuss the problem with you. 
If factory service is necessary, Targa will issue a Return Material Authorization 
(R.M.A.) number and give you instructions for customer prepaid shipment of 
the goods for repair. 

 

Products returned without an R.M.A. number, or returned C.O.D. will not be 
accepted by Targa. 

 

      3. If the product is covered under Targa's Limited Warranty, there will be no charge for 

parts or labour. 

 

      4. If the product is not covered under Targa's Limited Warranty, there will be a 

minimum charge for each item returned and a purchase order must accompany 
any returned goods. 

 
 
 
 
 
 
 
 
 
 

 

 

TARGA LIMITED WARRANTY 

 
Targa products are warranted for one year from the date of shipment.  Targa will 
repair or replace, for the original purchaser only, any defects in material or 
workmanship in the system components. 
 
No other representations or warranties, expressed or implied have been made by Targa 
Systems. Targa does not warrant that the system components are merchantable or fit 
for any particular purpose.  
 
Targa Systems  is not liable for any loss of profit or for any special, incidental or 
consequential damages resulting from the failures of its products. The sole liability of 
Targa Systems  is to repair defects in Targa products. 
 
This warranty is rendered void if the unit has been changed or modified other than by 
written instruction from Targa Systems.

 

Summary of Contents for DTU40/SA-40-2

















Reviews: