background image

MODELS

OUTPUT 

(Btuh)

FUEL

AD250

250,000

150-27993

Congratulations!

You have purchased the finest agricultural building heater available. 

Your new L.B. White heater incorporates the benefits from the most experienced

manufacturer of heating products using state-of-the-art technology.

We, at L.B. White, 

thank you

for your confidence in our products and 

welcome any suggestions or comments you may have...call us, toll-free, 

at 1-800-345-7200.

Owner's Manual and Instructions

GUARDIAN 

®

Agricultural Animal Confinement Building Heaters 

with 

Smart Sense

™ 

Automatic Variable Rate Heat

For Use with SmartBox

Controller

ATTENTION ALL USERS

This heater has been designed, tested and evaluated by L.B. White Co. Inc. as a

direct gas-fired circulating heater for the heating of agricultural animal confinement

buildings, and is approved for either indoor or outdoor mounting.  To utilize the Smart

Sense

automatic variable rate gas control valve, the heater must be connected to

an L.B.White SmartBox

and building environment controller.  If you are considering

using this product for any application other than it’s intended use,  please contact

your fuel gas supplier, or the L.B. White Co., Inc.

Patent Pending

Propane-Vapor

Withdrawal or

Natural Gas 

Summary of Contents for GUARDIAN Smart Sense AD250
































Reviews: