background image

114278-01C

3

18.  Never move, handle, refuel, or service a hot, 

operating, or plugged-in heater.

19.  Never attach duct work to front or rear of 

heater.

20.  Never attach heater to external fuel tank.
21.  Heaters  used  in  the  vicinity  of  tarpaulins, 

canvas, or similar enclosure materials shall be 

located a safe distance from such materials. 

The recommended minimum safe distance is 

10 feet (304.8 cm). It is further recommended 

that  these  enclosure  materials  be  of  a  fire 

retardant nature. These enclosure materials 

shall be securely fastened to prevent them 

from igniting or from upsetting the heater due 

to wind action.

22.  Unplug heater when not in use.
23.  Never block air inlet (rear) or air outlet (front) 

of heater.

24. 

Warning to New York City Residents

 

For Use Only At Construction Sites

 in ac-

cordance with applicable NYC codes under 

NYCFD certificate of approval #4803, #4899, 

#4908, #4909, or #4934.

UNPACKING

1.  Remove all packing items applied to heater 

for shipment.

2.  Remove all items from carton.
3.  Check  items  for  any  shipping  damage.  If 

heater is damaged, promptly inform dealer 

where you bought heater.

SAFETY INFORMATION

Continued

Side Cover

Fuel 
Cap/
Gauge

Hot Air Outlet

Side Cover

Fuel 
Tank

Hot Air 
Outlet

Fan Guard

Air Filter 
End 
Cover

Fuel Cap/Gauge

Ignition Control 
Assembly (On 
Inside of Side 
Cover)

Ignition Control 
Assembly (On Inside 
of Side Cover)

Figure 1 - 70,000 Btu Model

Figure 2 - 165,000 Btu Model

Thermostat Knob
(Thermostat 
Models Only)

Fuel 
Tank

Fan Guard

Thermostat Knob
(Thermostat 
Models Only)

ON/OFF Switch 
with Light

ON/OFF Switch 
with Light

PRODUCT 

IDENTIFICATION

Summary of Contents for CP070CK

























Reviews: