L-Acoustics KARA MODULAR WST SYSTEM Rigging Procedures Download

Page: 46 / 76

KARA

ODULAR

DULAR

DULAR WST

WST

SYSTEM

rigging procedures using

kara

kara----minibu

minibu

VERSION 1.0

KARA_SRM_EN_1-0

w w w . l - a c o u s t i c s . c o m

Attach SB18#2 to SB18#1 as follows:

Remove a T-BLP from SB18#2.

Rotate the link arm down.

Secure the link arm to SB18#1 by re-inserting the T-BLP into the SB18#1 top link point.

Repeat this procedure until all four arms are secured to SB18#1.

Figure 48: Attaching SB18#2 to SB18#1

Repeat steps 2 and 3 until all SB18 composing the array are assembled.

Assemble a KARA-MINIBU/KARA-MINIBUEX stacking platform as follows:

Turn the KARA-MINIBU so that the text of the identification plate is upside down.

Position a first KARA-MINIBUEX on the laser plate side of the KARA-MINIBU by turning it feet pointing down
and inserting the stud into the slit of the KARA-MINIBU located near the laser plate.

Drive 3 bolts to the 3 holes shown in Figure 49 (6 mm hex bit, 13 mm hex key, 7 N.m/63 in.lb

Repeat the procedure with a second KARA-MINIBUEX on the other side of the KARA-MINIBU.

Place the stacking platform in

rear extension configuration

only [9.3.1].

Figure 49: Assembling a KARA-MINIBU/KARAMINIBUEX stacking platform

IMPORTANT

Laser plate

a. Identification plate

KARA-MINIBU

c. Bolts (x3)

b. Stud inserted into slit

KARA-MINIBUEX (x2)

Rear

Front

Towards audience

(x4)

SB18#2

SB18#1

Summary of Contents for KARA MODULAR WST SYSTEM













































































Search results

Summary of Contents for KARA MODULAR WST SYSTEM

Reviews:

Related manuals for KARA MODULAR WST SYSTEM

Brands by name

Popular brands

L-Acoustics KARA MODULAR WST SYSTEM, Rigging Procedures

Search results

Summary of Contents for KARA MODULAR WST SYSTEM

Reviews:

Related manuals for KARA MODULAR WST SYSTEM

Brands by name

Popular brands