background image

Safety

Risk of falling objects

Verify that no unattached items remain on the product or assembly.

Risk of tipping

Remove all rigging accessories before transporting a product or an assembly.

Take into account the wind effects on dynamic load.

When a loudspeaker assembly is deployed in an open air environment, wind can produce dynamic stress to the

rigging components and suspension points.
If the wind force exceeds 6 bft (Beaufort scale), lower down and/or secure the product or the assembly.

Intended use

This system is intended for use by trained personnel for professional applications.

Read the OWNER'S MANUAL before installing the system.

Use the loudspeaker system components described in the manual and follow the operating instructions.

As part of a continuous evolution of techniques and standards, L-Acoustics reserves the right

to change the specications of its products and the content of its documents without prior

notice.

Check 

www.l-acoustics.com

 on a regular basis to download the latest document and software updates.

Do not expose the product to extreme conditions.

Do not expose the product to moisture (rain, mist, sea spray, steam, humidity, condensation…) or excessive heat

(direct sun, radiator…) for a long period of time.
For more information, refer to the 

Product protection ratings

 document, available on the website.

Read the maintenance section of this document before servicing the product.

Contact L-Acoustics for advanced maintenance.

Any unauthorized maintenance operation will void the product warranty.
Before sending a product to L-Acoustics for maintenance, save all user presets to les using LA Network Manager.

K3 owner's manual (EN) version 1.0 

 7

Summary of Contents for K Series

























































































































Reviews: