L-Acoustics K Series Owner'S Manual Download

Page: 40 / 120

Loudspeaker congurations

Additional downll element

All K3 system congurations can be combined with an additional Kara / Kara II line source downll system. This allows

an extension of the vertical coverage to the closer audiences.

Kara / Kara II

The Kara / Kara II enclosures are driven by the LA4X / LA8 / LA12X amplied controllers.

Enclosure

Kara II or Kara

Preset

[K3 70] [K3 90] [K3 110]

[KARAIIDOWNK3] [KARADOWNK3]

Frequency range (-10 dB)

42 Hz - 20 kHz

Do not add any delay between the K3 and Kara / Kara II elements of a mixed line source.

Using the Kara / Kara II system

Refer to the

Kara II owner's manual

for the operating modes of Kara / Kara II as a main system.

K3 owner's manual (EN) version 1.0

Summary of Contents for K Series

























































































































Search results

Summary of Contents for K Series

Reviews:

Related manuals for K Series

Brands by name

Popular brands

L-Acoustics K Series, Owner'S Manual

Search results

Summary of Contents for K Series

Reviews:

Related manuals for K Series

Brands by name

Popular brands