background image

• For 90 days after you purchase your Seabreeze 600, Kyosho will either

repair or replace, at no charge, any incorrectly made part.

• Make sure you SAVE THE RECEIPT OR INVOICE you were given when

you bought your model! It's your proof of purchase - and we must see it
before we can honor the warranty.

• To send your Seabreeze 600 in for repairs covered under warranty, you

should send your boat to Kyosho's authorized U.S. repair facility:

Hobby Services

1610 Interstate Drive

Champaign, Illinois 61821

Attn. Service Department

Phone: (217) 398-0007 9:00 A.M. - 5:00 P.M. Central Time M-F

• For details on your return, be sure to follow steps 1-4 under the "Repair

Services Available Anytime" section.

Limit of our Liability:

Our liability under this warranty is limited to the repair or replacement by Hobby
Services of defective parts and does not include cost of shipping to us. Hobby
Services does pay the shipping expense to return warranty items to you.

Exclusion and/or Voidance of Warranty:

This warranty does not apply to damage or defects resulting from misuse,
abnormal service, damage in shipment, damage resulting from a crash or
damage caused by the batteries. The warranty is voided if the model is
modified, altered or repaired by anyone other than Hobby Services. This
warranty gives you specific legal rights, and you may have other rights that
vary from state to state within the U.S. We are sorry, but we cannot be
responsible for crash damage and/or resulting loss of the boat, radio,
accessories, etc.

Repair Services Available Anytime:
• After the 90-day warranty has expired, you can still have your Seabreeze

600 repaired for a small charge by the experts at Kyosho's authorized U.S.
repair facility, Hobby Services, at the address listed under Warranty

Information.

• To speed up the repair process, please follow the instructions listed below:

1. Under all circumstances, return the ENTIRE system: boat and radio.

2. Make sure the transmitter is turned off and all batteries are disconnected.

3. Send written instructions which include: a list of all items returned, a

THOROUGH explanation of the problem and the service needed, and your
phone number where you can be reached during the day. If you expect your

repair to be covered under warranty, be sure to include proof of date of
purchase (your store receipt or purchase invoice).

4. Also include your full return address.

Repair charges and postage may be prepaid or billed C.O.D. All repairs

shipped outside the United States must be prepaid in U.S. funds only.

Specification and Description Changes
All pictures, descriptions and specifications found in this instruction manual are
subject to change without notice. Kyosho maintains no responsibility for
inadvertent errors in this manual.

Set up the radio system following the
manufacturer's instructions and as

explained below.

1. Install the batteries in the transmitter and

the receiver battery holders.

2. Extend the transmitter antenna.

3. Connect the steering servo, throttle servo

and receiver battery to the receiver.

4. Extend the receiver antenna.

5. Adjust the servo trims to neutral position.

6. Turn the transmitter on.

7. Turn the receiver on.

8. Operate the rudder and sail control.

Make sure the servo arms move in

proportion to the movement of the
steering wheel and throttle trigger.

9. Check that the rudder and sail

servos are in the neutral position. See
diagram at left.

10. Turn the receiver off, then the transmitter.

Summary of Contents for Seabreeze 600




























Reviews: