background image

— 1 —

 1. SAFE TESTING 

#

Electricity is dangerous and can cause injury and death. Always treat it 

with the greatest of respect and care. If you are not quite sure how to 

proceed, stop and take advice from a qualified person. This instruction 

manual contains warnings and safety rules which must be observed by 

the user to ensure safe operation of the instrument and retain it in safe 

condition.  Therefore,  read  through  these  operating  instructions  before 

using the instrument.

IMPORTANT:

1.  This  instrument  must  only  be  used  by  a  competent  and  trained 

person  and  operated  in  strict  accordance  with  the  instructions. 

KYORITSU will not accept liability for any damage or injury caused 

by misuse or non-compliance with the instructions or with the safety 

procedures.

2.   It is essential to read and to understand the safety rules contained 

in the instructions or with the safety procedures.

3.   The  symbol 

#

  indicated  on  the  instrument  means  that  the  user 

must refer to the related sections in the manual for safe operation of 

the instrument. Be sure to carefully read instructions following each 
symbol 

#

 in this manual.

#

 

DANGER

 is reserved for conditions and actions that are likely to 

cause serious or fatal injury.

#

 

WARNING

 is reserved for conditions and actions that can cause 

serious or fatal injury.

#

 

CAUTION

 is reserved for conditions and actions that can cause a 

minor injury or instrument damage.

Summary of Contents for 4118A

























Reviews: