manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

2H0/2HZ

1-4-34

(3) Image is too light.

(4) Background is visible.

(5) A white line appears longitudinally.

Copy example

Causes

Check procedures/corrective measures

Insufficient toner.

If the display shows the message requesting toner replenish-
ment, replace the container.

Deteriorated toner.

Perform the drum refresh operation.

Defective 
transfer 
charging 
output.

The connector terminals 
of the high voltage PWB 
make poor contact.

Reinsert the connector. Also check for continuity within the 
connector cable. If none, remedy or replace the cable.

Defective engine PWB.

Check if YC12-11 on the engine PWB goes low when main-
tenance item U101 is run. If not, replace the engine PWB.

Defective high voltage 
PWB.

Check if transfer charging takes place when CN1-2 on the 
high voltage PWB goes low while maintenance item U101 is 
run. If not, replace the high voltage PWB.

Copy example

Causes

Check procedures/corrective measures

Deteriorated toner.

Perform the drum refresh operation.

Dirty main charger wire.

Clean the wire or, if it is extremely dirty, replace it (see page 
1-5-37).

Copy example

Causes

Check procedures/corrective measures

Foreign matter in the developing unit.

Check if the magnetic brush is formed uniformly. Replace the 
developing unit if any foreign matter (see page 1-5-39).

Dirty shading plate.

Clean the shading plate.

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

Xyron FPO User Manual preview
FPO
Brand: Xyron Pages: 6
Xerox 7700 Setup Manual preview
7700
Brand: Xerox Pages: 2
Xerox 7700 Setup And Quick Reference Manual preview
7700
Brand: Xerox Pages: 40
Xerox 7700 Advanced Features And Troubleshooting Manual preview
7700
Brand: Xerox Pages: 69
Xerox 7700 Install Manual preview
7700
Brand: Xerox Pages: 42
Canon Sure shot 80 tele User Manual preview
Sure shot 80 tele
Brand: Canon Pages: 24
Canon iPF720 - imagePROGRAF Color Inkjet Printer Brochure & Specs preview
iPF720 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 8
Canon i475D Series Setup Instructions preview
i475D Series
Brand: Canon Pages: 2
Panasonic KX-P8415 Operating Instructions preview
KX-P8415
Brand: Panasonic Pages: 3
Panasonic KX-P7105 Operating Instructions preview
KX-P7105
Brand: Panasonic Pages: 4
Samsung ML-6050 Manual Del Usuario preview
ML-6050
Brand: Samsung Pages: 82
Samsung ML-2525 Datasheet preview
ML-2525
Brand: Samsung Pages: 2
Xerox C410 User Manual preview
C410
Brand: Xerox Pages: 262
Canon ColorWave 3800 Operation Manual preview
ColorWave 3800
Brand: Canon Pages: 358
Oki MC560n Specifications preview
MC560n
Brand: Oki Pages: 4
Olivetti ARTJET 20 User Manual preview
ARTJET 20
Brand: Olivetti Pages: 22
Oki C7500n Maintenance Manual preview
C7500n
Brand: Oki Pages: 192
Lexmark 16C0365 - 5500 MFP Service Manual preview
16C0365 - 5500 MFP
Brand: Lexmark Pages: 88

Brands by name

Popular brands

Load more brands