manualshive.com logo in svg

Kyocera KM-2560, Service Manual

The Kyocera KM-2560 is a high-performance multifunctional printer designed for office use. With its advanced features and efficient functionality, this product delivers exceptional quality prints, copies, and scans. To access the Service Manual and user manual for free, you can conveniently download them from manualshive.com.

Share
Download
background image

2H0/2HZ

1-5-37

(2) Detaching and refitting the main charger unit

Follow the procedure below to replace the main charger unit.

Procedure

1. Open the front cover.

Figure 1-5-68

2. Pull the main charger unit.
3. While pressing the lock lever and remove 

the main charger unit.

4. Replace the main charger unit and install 

the unit.
The main charger unit, when fully inserted, 
must be set aside towards the drum unit.

Figure 1-5-69

Front cover

Lock lever

Drum unit

Main charger unit

Main charger unit

Summary of Contents for KM-2560









































































































































































































































































































































































































Reviews:

No comments

Related manuals for KM-2560

IBM 3130 Planning Manual preview
3130
Brand: IBM Pages: 112
Oki 6150 Setup Manual preview
6150
Brand: Oki Pages: 40
Saxxot CRU-158 Operation Manual preview
CRU-158
Brand: Saxxot Pages: 13
Oki C5550 MFP Reference Manual preview
C5550 MFP
Brand: Oki Pages: 167
Oki C610dn Manual De L'Utilisateur preview
C610dn
Brand: Oki Pages: 116
Oki C610dn Material Safety Data Sheet preview
C610dn
Brand: Oki Pages: 52
Oki C6000dn Manual Do Utilizador preview
C6000dn
Brand: Oki Pages: 331
Oki C6000dn Setup Manual preview
C6000dn
Brand: Oki Pages: 36
Oki C5800Ldn Series Reference Manual preview
C5800Ldn Series
Brand: Oki Pages: 143
Oki C710dn Guía Del Usuario preview
C710dn
Brand: Oki Pages: 101
Oki C710 Brochure & Specs preview
C710
Brand: Oki Pages: 6
Oki B6250dn Safety And Warranty Manual preview
B6250dn
Brand: Oki Pages: 36
Oki C6050dn Manual De L'Utilisateur preview
C6050dn
Brand: Oki Pages: 282
Oki C6050dn Guía Para El Usuario preview
C6050dn
Brand: Oki Pages: 269
Oki B4545 MFP Safety And Warranty Manual preview
B4545 MFP
Brand: Oki Pages: 36
Oki B2500 Specifications preview
B2500
Brand: Oki Pages: 2
Oki B6100n Installation Manual preview
B6100n
Brand: Oki Pages: 3
Oki B6100n Safety Information Manual preview
B6100n
Brand: Oki Pages: 6

Brands by name

Popular brands

Load more brands